Search results

  1. kpack5982

    Quadrant spacers...?

    I marked the place where the quadrant sat once I had it tightened, then loosened the cable up and put washers in, but only to ease my mind a little.
  2. kpack5982

    Shifted Hard Now Driveline Vibration

    Thanks a lot for the suggestions. I'm gonna get under there this afternoon and try to find the culprit. Maybe a lose driveshaft bolt or something that's an easy fix.
  3. kpack5982

    Shifted Hard Now Driveline Vibration

    It doesn't shake at all in neutral or while I'm rolling. And it shakes in all gears. It still doesn't like to shift into gears as smooth as it should, but it does go into gear ( i have a pro 50 short throw if it matters) And the more rpm the car spins, the more the shifter vibrates
  4. kpack5982

    Shifted Hard Now Driveline Vibration

    anyone?
  5. kpack5982

    Shifted Hard Now Driveline Vibration

    Well this weekend I was out in my 93 mustang and for some reason it didn't want to go into gear. I adjusted the adjustable quadrant I have further, thinking maybe the clutch cable stretched, and the shifting problem isn't as bad getting it into gear, but when I drive the shifter vibrates...
  6. kpack5982

    I NEED HELP...JUST INSTALLED A 70MM TB

    Try resetting the idle and see if that helps it run any better. I usually reset mine every time I tamper with something. Ford Mustang Base Idle Reset
  7. kpack5982

    water temp gauge wiring help pleaseeee

    :stupid: http://www.autometer.com/download_instruction/1079A.pdf
  8. kpack5982

    Need a tune IA

    I don't know how far away you are from the des moines area, but lund motors in waukee does dyno tuning. They used to be primarily mustang based but expanded their operations. They have a website too but don't have it offhand. They definitely know their mustang stuff tho.
  9. kpack5982

    Need experienced help with intake setup

    I'd think you shouldn't have problems. An a/f gauge my benefit you, but basically you just need to tune the fuel pressure to where it runs best at wot. Do like 3 time runs at each fuel pressure, 38, 39, etc then average it and set it to where it runs the fastest. The computer should be able...
  10. kpack5982

    best place to get synchros?

    +1 for THESOURCE. Really good guy to deal with.
  11. kpack5982

    Wheel stud replacement

    well I don't have a press myself, would an auto parts store be able to help me here or what would you recommend?.....
  12. kpack5982

    Wheel stud replacement

    Do I need to take the caliper and rotor off to get a stripped stud out, or can I just hammer the thing out, without taking anything but the wheel off?
  13. kpack5982

    Electric Fan Spal Controller???

    sorry didn't mean to play devil's advocate there, but you could run the controller to another relay, like a bosch 75 amp and have the controller basically control the powering of the fan. That's what I did temporarily anyways with my controller when it was blowing the fuse on the controller.
  14. kpack5982

    After lowering and c/c plates alignment still off

    All stock suspension other than the pro kit. I do have some bumpsteer so maybe a kit isn't a bad idea anyways. i'm gonna take it to a different shop when I install those, maybe then they can figure out what is goin on. the c/c plates did help a little, but apparently not enough. I'll be...
  15. kpack5982

    After lowering and c/c plates alignment still off

    for a fox. and it's more than just a little off....
  16. kpack5982

    Electric Fan Spal Controller???

    I wish I could help, but I've decided to say hell with my fan thing too, I had a hayden controller and the wiring wasn't meant for my mark viii fan so I put the stock one back on for the time being until I can get a controller designed to deal with the amperage pull. Good luck with your search...
  17. kpack5982

    After lowering and c/c plates alignment still off

    Well my car has been out of commission until i put a new fuel pump in and now its running right, but the alignment is still off. It has an eibach pro-kit and mm c/c plates but the shop that did it said that was as far as they could get it aligned and the wheels still are farther apart on the...
  18. kpack5982

    relay for electric fan/

    well I looked everywhere but no one had the switch in town for the 79 to 82 vw rabbit that I was lookin for. My question is tho, I had that haynes controller for a while, but the wiring in it just isn't up to par for the mark viii. Could I splice in the push in probe and try to use that or is...
  19. kpack5982

    Fuel Pressure Issues

    Could be a plugged fuel filter. I'd also check for vac leaks and see if you have a cracked line somewhere. That's all i can think right now.
  20. kpack5982

    relay for electric fan/

    thanks for that link. If i don't find one at the parts stores this weekend I'll order that, looks like it'd work perfect. Anyone know of any that may be carried at a parts store by chance?
Top Bottom
Back
Forums
Menu