Search results

  1. Y

    What ive done so far with Codes

    ttt
  2. Y

    What ive done so far with Codes

    I doubt the wires seeming mixed up has anything to do with it. I had the codes read about a year ago and I got No Defects. Im sure if the wire was backwards it woulda pinged back then
  3. Y

    What ive done so far with Codes

    Upon further investigation I have found that the wires seen to be mixed up? Matching it up with this diagram here: http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif The white/Orange wire is where the Black/white should be and vice versa The green is in the correct...
  4. Y

    What ive done so far with Codes

    Ok I found the EGR Sensor When I read the volts it was off the table on the 10V setting and when I switched it to the 250 setting I got no reading. Im at a loss
  5. Y

    What ive done so far with Codes

    Ok No readings at the TP....Wire is dead Now where is the EGR Sensor? Anyone?
  6. Y

    What ive done so far with Codes

    Worse case scenerio what am I looking to spend in repairs?
  7. Y

    What ive done so far with Codes

    Ok this is what I got Orange/ White wire - Seems to be dead. I get nothing from it Black/white - at about 5 ohms with engine off Pin 45 - 9ACV How I tested the wires was I put a Pin in the female end and used my volt meter. I dunno if that matters just wanted to throw that out there...
  8. Y

    What ive done so far with Codes

    edit see below
  9. Y

    What ive done so far with Codes

    Just did the test again and got the same codes 22 and 12 and then 99 on the engine on run
  10. Y

    What ive done so far with Codes

    Ok why would a 22 come up after I changed the Sensor the 22 is there for? Im also curious about the 99 I got when I ran the engine on test
  11. Y

    What ive done so far with Codes

    Ok cool Batt is now disconected. Should I run both diagnostics? Engine on and Engine off?
  12. Y

    Are MAP Sensors and BARO Sensors the same?

    Left it open... Please refer to my new topic about the codes I got and what ive done so far. Thanks I just wanna keep my problems organized :nice: Please check out my new post maybe you have some idea's
  13. Y

    What ive done so far with Codes

    Ok heres what ive got/done so far. I dumped some codes: 22 (With engine off) It says MAP Sensor, BARO on the codes. What I did was replace the Sensor. ( I Used a MAP sensor cause I was told on here they are the same) 12 Idle Speed Control or Air Bypass ( I have done nothing with this as of...
  14. Y

    Are MAP Sensors and BARO Sensors the same?

    Replaced it And I am still getting the 22 code along with 12 any other suggestions?
  15. Y

    Are MAP Sensors and BARO Sensors the same?

    Ok cause I pulled a code sayin something was up with my BARO sensor So I bought this MAP sensor without thinking After I install this new sensor should I drive it around the block a few times to break it in?
  16. Y

    Are MAP Sensors and BARO Sensors the same?

    My car is a 90 5.0 Mass Air I dunno if its actually a "Cap" on the connection so to speak its just a white knob looking thing. But my original question can I use this new MAP sensor I bought? Does it work the same as the BARO Sensor Thanks again
  17. Y

    Are MAP Sensors and BARO Sensors the same?

    Ok so bare with me. The one I have on the car now.... It looks exactly the same as this one. except there is a white knob over the vacuum connection. Can I use this new Sensor I bought and just put that white knob over the new connection? Or am I out the 60 bucks and have to buy a new BARO sensor
  18. Y

    Are MAP Sensors and BARO Sensors the same?

    I think I screwed up I bought a MAP Sensor thinking thats what I needed. I was reading through some past post and seen that my car doesnt use a MAP sensor but a BARO. Do I have to bite the bullet on the 60 bucks I just spent for this MAP Sensor? Thanks and sorry for the post's I wanna know...
  19. Y

    Changing MAP Sensor

    oh man please tell me I didnt just drop 60 bucks on the wrong part. Was I supposed to buy a baro sensor or are they both the same? man oh man I dont know if I can return this either if I messed up
  20. Y

    Changing MAP Sensor

    SHAZBOT! I think I bought the wrong part! Help Please I dumped codes and it said my MAP Sensor which is code #22. So I got a new one. I notice the old map sensor has a white nob on the left side next to the electrical connector. Is there supposed to be something else there and im missing it or...
Top Bottom
Back
Forums
Menu