Search results

  1. GTWayne

    EEC Code 124: TPS voltage higher than expected?

    Getting a softcode 124: TPS voltage higher than expected. I looked at the datalogs and TPS voltage ranges from .994 to 4.87. Did a quick datalog KOEO to see if the TPS was noisy or going bad and it isn't, I'm getting nice clean linear voltage and no apparent flat spots. Didn't have this...
  2. GTWayne

    Wheel Spacers, which ones?

    Wheel spacers I have the Maximum Motorsports 1" spacers with the studs built in. I've never had a problem with them. Wayne
  3. GTWayne

    Anyone with Lokar Oil Dipstick in 94/95??

    Lokar ED-5004 thanks, I'll give it a go. Wayne
  4. GTWayne

    Vortech Owners w/ Autometer Oil Pressure Gauge....Question!

    Vortech w/Autometer oil press gauge I must be the real oddball here and it must be due to my old pipefitter back ground. I fabricated a plumbing tree that mounted the Vortech supplied fittings, Stock sender and Autometer sender. I'd send pictures but our digital camera was stolen along with...
  5. GTWayne

    Anyone with Lokar Oil Dipstick in 94/95??

    I bought the Model ED-5004 which was supposed to fit 302 to yr 95 but another guy said I had the wrong one. Anyone have one and which model #?] Wayne
  6. GTWayne

    Did you see the March 2004 5.0 Mustang Mag yet?

    04 5.0 Mag <marquee direction=right> :banana: "C O N G R A T U L A T I O N S, PAUL!" :banana: </marquee> Wayne
  7. GTWayne

    LoL! look at this dumb ricers excuses!!

    Ricer excuses, don't get no better than this Clutch my A??, whose he trying to kid. That was too much. <marquee direction = right> :lol: :spot: :banana: :stupid: :doh: </marquee> Wayne
  8. GTWayne

    First Dyno numbers for S-Trim

    Torque number, Nice Vibe, You're right and the seat of my pants really loves it. I'm gonna have to get something stickier that these Nitto DRs cause I can light em up any time w/o full throttle. I'm hoping the new MT Drag radials will hold it...those will be my spring present... Wayne
  9. GTWayne

    Stangnet 94/95 Member of the Year - Congrats to KillerCanary!

    Stangnet Member of the Year Congrats Paul. Well deserved. I must add congratulations as well to all the other nominees, they deserve a lot of credit as well. Wayne
  10. GTWayne

    First Dyno numbers for S-Trim

    FastmanGT, Tranny held fine, no slipping noticed at all. We started the pull in top gear at 3800 rpm. Ran all the way to 6500. Wayne
  11. GTWayne

    First Dyno numbers for S-Trim

    RC, You missed my reply earlier in the thread. I was reading the boost gauge from across the car and at an angle. When I talked w/the guys at the dyno and went back to relook, it was 10/11 psi not 14. Its like reading the speedo about 5mph higher from the pass side... Yep the A/F was...
  12. GTWayne

    First Dyno numbers for S-Trim

    Not planning on going any leaner than 12:1. The Vortech FMU is currently a 4:1 and want to see if they have 3:1 and 2:1 disks. We can do the bottom end w/the Kirban but would like to flatten out the top with the FMU. The run was set w/the boost retard at 1. Complete mod list is on our web...
  13. GTWayne

    First Dyno numbers for S-Trim

    No graphs at present. Numbers peaked early around 4800, that's why we figure we can make much more by leaning out the A/F. As far as boost goes, I guessed at the number to a degree. I was on the other side of the car datalogging with my TweecerRT and was looking at the cowl mounted boost...
  14. GTWayne

    First Dyno numbers for S-Trim

    Took car to "The Dyno Edge" today to make sure we had safe A/F. Only made one pull because we need to lean out the top end and I want to keep the FMU so I need to get some ratio disks for it. Motor was rich and loosing power from 5600 - 6600 (10:1 A/F). Made the numbers on 14 psi. We figure...
  15. GTWayne

    Throwning codes after Vortech install, any Ideas?

    Got these codes after installing my AFM Vortech S-Trim stg I kit. I've gotten the same codes wether I'm using the stock W4H0 binary or my JMS tune. 511: Electronic Control Assembly (ECA) problem, Read Only Memory test failure. 124: Throttle Position Signal voltage higher than expected...
  16. GTWayne

    EVERYONE...Post 1 or 2 of your FAVORITE PICS of your Car!

    Favorite pic of my car my photo was too big, RC edited it for me later in the thread... Wayne
  17. GTWayne

    Couple of New Pics

    Looks nice RC, Where did you get the Red hose for the inlet to the TB. I'd love to replace my blue with red. Wayne
  18. GTWayne

    Need valve covers that cleak Twisted Wedge heads

    Valve covers I have the Black ones lke Green 94 and they clear my Crane 1.6s. Wayne
  19. GTWayne

    Pics of my new AFM Vortech kit installed

    Blow by RC let me know if you guys decide to do it. I'd like to know how it works out and some pics of the results. I'm going to try and reroute my bypass hose this weekend. Wayne
  20. GTWayne

    Driveshaft loops

    Driveshaft loop HPM... Wayne
Top Bottom
Back
Forums
Menu