Search results

  1. J

    cobra fast

    foolish
  2. J

    bad dyno numbers.....

    Does anybody read before they post??? I always thought it didn't matter how big the injector was as long as the maf if calibrated. If you have overkill, that doesn't mean it will run bad does it? I know a guy that ran 42's on a stock motor with a big turbo, then sold the turbo and still runs the...
  3. J

    New Engine Woes *please help*

    I have a friend who has fried 5 mallory boxes, he swears the're junk.
  4. J

    Ebay valve springs for GT40P heads......

    Watch it with the springs, I bought the trickflow springs, and after bending all my pushrods, realize that the heads have to be machined for the springs to work.
  5. J

    EFI DIZZY DOES WORK WITH CARB! Now I have 2 much fuel pressure

    So, in theory, you could hook up a tps to the carb linkage, and since it is sd, just hook the rest of the sensors up, and you would still have a timing curve. Even if it was mass air, you could probably pipe up a sensor to an air cleaner and go that way, it wouldn't be 100% accurate, but I think...
  6. J

    Ok, since I screwed myself what springs do I need?

    I have a tfs stage one cam, with stock heads. Anyone have a part number or an idea what spring I should use? Obviously the tfs springs I have aren't going to get the job done.
  7. J

    HELP Bent pushrods why?

    ttt
  8. J

    Opinion on a 86 Mustang

    If third is blown up, it will cost more than 100 to fix. But it's probably a good deal anyways.
  9. J

    rim scrapes

    balljoints.
  10. J

    94 clutch pedals fitment into 87 stang

    No they won't.
  11. J

    HELP Bent pushrods why?

    Is there any spring I can get and throw them on? I'm sure the springs are the problem. I guess the car sits untill I can get enough money to get some thumpers.
  12. J

    HELP Bent pushrods why?

    How could I change the install height? I think I got screwed. These springs are like 3 in one. they have a lot of tension. I don't really know what to do, how can I tell if they are stacking? I didn't like the way the springs went on in the first place, this speed shop ordered them to match the...
  13. J

    HELP Bent pushrods why?

    I couldn't have hit valves, my lift is 5.12 on the intake and 498 on exhaust. I upgraded to the trickflow springs because of the cam lift. I don't see how they could coil bind, because they are matched for the cam. It never sounded like it was smacking valves, it just made a little loose rocker...
  14. J

    Heavy white smoke on hard acceleration

    White smoke = Blown Head gasket, sorry about your luck.
  15. J

    HELP Bent pushrods why?

    edited, so bump
  16. J

    HELP Bent pushrods why?

    That's what I'm hoping, i didn't over rev it, it was just idling, i reved it to like 3-4g a couple times, but no problems, I was walking away from it when it went to hell. I'm gonna get some good pushrods and try it again.
  17. J

    HELP Bent pushrods why?

    I think maybe the springs are too much for the stock pushrods, anyone agree?? Anyone have any experience with frpp pushrods?
  18. J

    HELP Bent pushrods why?

    no, ran fine, just bent all the pushrods
  19. J

    Please help.. possible dsamage to my motor!

    I'm saying bearing, only because it has been run out of oil.
  20. J

    HELP Bent pushrods why?

    HELP Bent pushrods and broken rocker why? I just fired up my car, it was running, pretty rough, set the timing, then started sounding funny, I thought maybe dropped a valve or a rocker came off. Pull the valve covers, and my pushrods are bent to hell. I used trickflow springs with all the stock...
Top Bottom
Back
Forums
Menu