Search results

  1. tim281

    What Mufflers???

    I agree... The sound of flows is far superior to anything else. I went flows and an hpipe to get the deep muscle car sound. No xpipe or straight thru muffler 4 me.
  2. tim281

    Magnaflow cats Vs other cats

    I got a magnaflow hpipe with cats new for hot exhaust online for 320.00 delivered. All stainless steel construction and 2.5" piping. Very nice quality.
  3. tim281

    5.0 problems

    Sorry for the thread hijack, but I was wondering why it is bad to run platinum plugs in a NA mustang? I thought they were only bad with forced induction. What symptoms do platinums exhibit?
  4. tim281

    ANSU injector cleaning

    I paid $20 an injector which is kind of high, but i had same day turn around. If you go through ebay they are about 40 bucks cheaper overall.
  5. tim281

    ANSU injector cleaning

    Dropped off my original 19# injectors at a local shop for the ANSU clean & test. The injectors had 102k miles on them prior to the testing. 1 of the 8 injectors was failed the pressure leak test. 3 of them had bad spray patterns while the others were all fair. The Flow rate was about 12%...
  6. tim281

    dynamat to reduce heat and noise?

    MGW sells a rubber boot for the shifter, check of out on their website, it is listed with the shifters. I wonder if doing mass backed carpet would help more than dynamat? I added a lot of dynamat to the doors and trunk of my saleen and I can't say there was a huge difference. I personally...
  7. tim281

    Difference between GT40, Cobra, and tubular GT40?

    I just installed a gt40 tubular with a 1" phenolic spacer, it barely clears the hood. The casting models maybe a bit taller so I am not sure if you can run the 1" spacer with them? I bought the tubular upper off craig's list for 300.00 and purchased a gt40 explorer lower off ebay. I have...
  8. tim281

    dynamat to reduce heat and noise?

    I have 2ch american thunder flows, BBK shorties, and Magnaflow Hi-Flow H-pipe with Cats...zero drone.
  9. tim281

    Difference between GT40, Cobra, and tubular GT40?

    Tubular is lightest in weight since it is sheetmetal design as opposed to thicker castings. Otherwise I think they are basically the same design.
  10. tim281

    BBK TB installed

    It is the tubular gt40 intake, it is 75mm.
  11. tim281

    Code 34, 41, & 91 - any guesses

    Trying to track down the culprit for these codes!! Any help is appreciated... Engine Off Test: 34, 67 Engine On Test: 41, 91, 34 I would imagine that this has something to do with the EGR/EVP system (34) and it is probably making the car lean (41&91), right? Since I get code 34 when the...
  12. tim281

    BBK TB installed

    Installed the 75mm TB along with my GT40 intake this weekend. I also installed the BKK EGR spacer and C&L inlet pipe also. Just wanted to say that I do not have any TB whistle at low speeds or idle. I did notice a slight whistle when I first start the engine but it is very brief and only at...
  13. tim281

    Pioneer Balance runs great

    Installed a Pioneer Balancer that I got from Summit Racing and it dramatically smoothed out the engine and RPM roughness. The OEM one looked a little out at idle but I really noticed the rough engine under heavier loads. I also had an occasional vibration or rattle when the car was in gear but...
  14. tim281

    1" spacer & GT40 Tublar

    Thanks for the note. Anyone else with a GT40 Tubular & 1" spacer remember if they ran the A/C line under the intake??
  15. tim281

    How to get tint adhesive off with out destroying rear defroster...

    I have seen rear window defroser repair kits at NAPA. I am not sure how good they work, but it looks like you just paint across the shorted section with a conductive paint or something.
  16. tim281

    1" spacer & GT40 Tublar

    It looks like my GT40 tubular and 1" spacer will fit under the stock hood without clearance issues. The hood shut just fine. The A/C hose going to the accumulator was a bit stiff and a bit hard to push out of the way. The hose is probably going to have to stress relieve a bit in its new...
  17. tim281

    BBK strut brace & intake

    That brace in the Ebay ad is not like the BBK brace in my car. My BBK has the bolts on the outside of the tube connection at the firewall location. I am planning to install my GT40 tubular intake with a 1" spacer this weekend. I doubt the BBK will fit with my 1" spacer. The MM brace fits all...
  18. tim281

    Cat back for the 93

    Flowmaster American Thunder! I love the muscle car sound and have zero drone. I have a cat hpipe also.
  19. tim281

    ac wire for dc fan control?

    Great information, I will go lpcs route when I do the install. BTW, any good tips or tricks for quick and clean ways to probe the wires through the connector. Seems like a sewing needle through the weatherpacking might be best?
  20. tim281

    ac wire for dc fan control?

    I am not famaliar enough with fox body electronics to exactly know what you are talking about? Can you please explain the to me what the LPCS & IIRC is? Thanks!
Top Bottom
Back
Forums
Menu