Search results

  1. J

    Does this sound right?

    Just hooked up a scan gauge and this is the readings I get water temperature: ranges from 195-210 temp idle rpm : 750-800 rpms too low??? ign time : idle 6-8deg press gas jumps to 26-29 batt volts : 13.2 - 13.6v idle
  2. J

    Car rpms dropping quick

    Yes, it has a p0500 speed sensor malfunction, but the speed sensor has been replaced. I can rev the car and at 2000 to 2200rpms it seems to shake/miss and then the check engine light will pop up that code ?
  3. J

    Car rpms dropping quick

    no, already have a new one
  4. J

    Car rpms dropping quick

    I have the bosch stock bypass valve, just wondering if that would cause the car to do this, it has been on the car since I purchased it 3 years ago thinking it may have went out?
  5. J

    Car rpms dropping quick

    I can drive it, just got to be carefull not to leave it in neutral while rolling, or it will surge a couple of times and then die. It ildes fine with the car not moving, but if you get going about 30+mph and put it in neutral it just will not stay at an rpm it will drop and surge then die. I...
  6. J

    Car rpms dropping quick

    My 98 cobra will drop rpms very quick if I shift to neutral while cruising down the road, it will drop to about a 1000rpms surge up to 1400 then back down and die. I have replaced IAC, Throttle body, tps is set on 1.00v, dpfe sensor, I know lot of guys have the problem with the idle hanging...
  7. J

    O2's

    ? Is he a member on here or have a website?
  8. J

    O2's

    Anyone know where I can get some ford o2 sensors for the front o2's on a 98 cobra for a good price ??
  9. J

    Ok to unhook computer???

    Ok so its ok to unhook and hook back up, one other question, what about hooking up a new computer to it, the same computer but just a new one, would that affect anything??
  10. J

    Ok to unhook computer???

    Is it ok to unhook the computer on a 98 cobra without running into any problems with security or reprogramming anything?? I know I have the computer chip in my key and was hoping this wouldn't have to be reprogramed, so can I just unhook the computer and then hook it back up and be ok??
  11. J

    Location of abs control module????

    Anyone know where the ABS control module is located on a 98 cobra, would the be the box that is in the passenger side inner fender that has a harness hooked to it and a screw holding the harness??
  12. J

    Need help, car stuttering

    I keep getting this P0500 which is speed sensor malfunction, I have already replaced this sensor, but It still will set the code, I notice that the check engine light comes on while I am reving the car sitting still and it will be p0500 speed sensor. I checked the volts to the speed sensor...
  13. J

    Need help, car stuttering

    should not be, new fuel filter/pump and injectors, the egr is also new
  14. J

    Need help, car stuttering

    I have been having a stutter problem for a couple weeks now, it pulls the code p0500 which is the speed sensor, but I have already replaced this with a new one. My idle will hang sometimes and the car will stutter under low rpms going down the road. I have noticed that I can get the check...
  15. J

    afm pipe install

    Does anyone know a good way to lower the passenger side of a radiator on a 98 cobra?? I have installed the afm powerpipe, notched the hood and tryed several ways to keep it from hitting the hood, but it still slightly rubs it. I read that someone had lower their passenger side of the radiator...
  16. J

    Throttle body ?

    Has anyone heard of a problem with throttle body shafts leaking, I noticed that my twin 65mm bbk throttle body has air comming out around the shaft where the throttle cable connects too. Does anyone know of a fix for this or will I need a new throttle body, if so which one would be a good...
  17. J

    Supercharger Pulley

    I can't get the pulley to come off of my vortech supercharger, it seems to be stuck somehow. Has anyone ever used a sterring wheel or harmonic balancer pulley on the pulley to get it off, anyone got any ideas on how to get this off.
  18. J

    boost pipe??

    Anyone know of a polished boost pipe for a 98 cobra with vortech?? I got the afm power pipe and I like it but its just too close of a fit, even with trimming the hood it still will hit slightly as the motor torques. Anyone know of any other company that makes pipes for the vortech, I know...
  19. J

    Bypass valve

    How do you check to see if a bypass valve works, I have a vortech mini race bypass valve and want to see if it operates properly. I can get it to open slightly with slight vacume but it doesn't seem to open up all the way. Anyone got any ideas
  20. J

    AFM Pipe Pictures please

    Anyone got a 96-98 cobra with an AFM powerpipe installed, mine has been giving sooo much grief. I have notched the hood, cut the inner finder and did everthing I know of and the hood still hits on the pipe when I try and close it, I do have an aftercooler also but that shouldn't bother it Thanks
Top Bottom
Back
Forums
Menu