Search results

  1. blascrw

    8.8 fitment in 66?

    hmmm Could we condense the info here and put it in as a FAQ or Sticky?? It is useful info...and I would like to see a listing... 65 -66 use axle A do this, use these wheels 67-68 use axle A do this, use these wheels... 65-66 use axle B do this, use these wheels... and so on...
  2. blascrw

    05 - 06 bullitt rims BS??

    sorry my bad...didn't realize yours were 05+ bullits...
  3. blascrw

    G2C Proto-type Brackets Now a Reality

    I know I completely understand. Looks like nice work... I never went the Granada route...almost did...so I bought MustangSteves...I am looking at the rear soon...depending on whether I replace the entire rear or not.
  4. blascrw

    G2C Proto-type Brackets Now a Reality

    looks good Looks darn good to me... How about a shot of the raw bracket?? I admire the effort you have put into this...
  5. blascrw

    8.8 fitment in 66?

    then.... So then you are saying 05+ wheels and a fox 8.8 is what I need? and no fox 8.8's had 5 lug and discs??
  6. blascrw

    05 - 06 bullitt rims BS??

    ok... So what do i need to run them on a 66? I am considering changing rears... what rear should I consider to not have to run spacers on the rear?
  7. blascrw

    8.8 fitment in 66?

    soooo.... A fox 8.8 rear with 05+ bullitts will work on the rear realatively easy with no spacers?? Is this correct?
  8. blascrw

    05 - 06 bullitt rims BS??

    Can anyone tell me what backspacing the 05 - 06 bullitts have?
  9. blascrw

    8.8 fitment in 66?

    I am confused too... I think I might just pull my original and sandblast and paint it and put it back in :( I want better gears and I am really toying with the idea of an AOD... I want bullitts but looking for some used so not sure what year they will be from. I want discs but we will see...
  10. blascrw

    8.8 fitment in 66?

    bringing up the past... So can someone lay this out in plain talk??? I am looking for what to do with the rearend... So a '79-04 rear will basically bolt up? no shortening? just cut off the ears? but none of those had 5 lug from the factory?? debating on what to do?? 9"...
  11. blascrw

    Good front drum to disc conversion kits....

    brakes I just purchased this kit 2nd hand ...never used... I cannot wait to get it on the car... saving now for a major push on the work... I am going with factory bullitts for now... maybe so vintage wheel works down the line... I got the red calipers and not sure if I will keep...
  12. blascrw

    Need a list of cars with 9" rears...

    few sites http://www.woodyg.com/fairlane/finfo/fordrears.html http://www.kevinstang.com/Ninecase.htm http://dfwmotorsport.com/Fairlane/9inchrearends.htm Think I have some more at work...I'll look Monday.
  13. blascrw

    So why is this turbo kit so cheap?

    worth it I have been playfully looking into a turbo setup... This looks to be worth it for the parts. i would assume it would still require a fair amount of fab work to fit in anything other than a fox body. If you start fabing you loose the pretty looks... So... having said that...
  14. blascrw

    13" Cobra Brake kit

    brakes Hey you have PM and email...
  15. blascrw

    Installing subs need amp advice

    addition Sorry... parallel is the +'s wired together and the -'s wired together speakerA SpeakerB +--------------+ | | | + terminal on amp Same for - terminals
  16. blascrw

    Installing subs need amp advice

    4 ohm is the usual for car 8ohm usual for home... if you connect 2 4ohm speakers in parallel you get 4 ohm the lower the ohm the greater the power until you reach the point of clipping of beyon the amps ability. So if the wedge has 2 speakers at 8 ohm each you can wire them in parallel and...
  17. blascrw

    TONS OF STOCK MOTOR STUFF and an FMX trans for sale

    parts tried to PM you...but you are full... give me a price on the engine 289 (is it complete minus intake and carb? any pics?), and both sets of heads... Thanks
  18. blascrw

    TONS OF STOCK MOTOR STUFF and an FMX trans for sale

    parts well I was interested in the 351 heads if they were windsor heads. Let me check with my wife and see if she is willing to make a visit anytime soon.
  19. blascrw

    TONS OF STOCK MOTOR STUFF and an FMX trans for sale

    darn if it was not needing to be gone this weekend...and I could convice my wife of a road trip (relatives in Largo) I would be interested in the heads and 66 engine...too much to ship...sorry!
  20. blascrw

    Cobra Brake Question

    CMM What you are referring to is a CMM (Coordinate MEasurement Machine) These are usually used to inspect a product to ensure it is whitin spec (tolerances). I can be used to plot the point and then tie in to a CAD/CAM software. I worked for a machining company (large industrial) The...
Top Bottom
Back
Forums
Menu