Search results

  1. R

    Transmission cooler

    For an aftermarket cooler; (on our sn-95 cars) the aux cooler needs to be connected to the bottom connection on the radiator, am I right?
  2. R

    Auto Stalls when put into Drive or Reverse

    I know that ram360 has probably solved his problem, but couldn't that problem (slow engaging into reverse and drive) also be caused by using a higher stall torque converter?
  3. R

    Rear main seal (transmission - driveshaft seal)

  4. R

    Rear main seal (transmission - driveshaft seal)

    When pulling the old seal out (rear main seal) did you guys use the stroker for leverage.. Where would I place the flat head screw driver to pull that seal out, on the inside diameter or on the outside diameter in respect to the seal itself?
  5. R

    Transmission seal (where the torque converter is located)

    Ok, finally figured out where the rear main seal is at, between the engine and flex plate. What I ended up taking out (in the first post) was the transmission pump seal out (between the Torque converter and transmission mate). there seems to be some noticeable oil drops from the back of the...
  6. R

    Transmission seal (where the torque converter is located)

    Well im starting to put the tranny back in the car; Im installing a Red line torque converter, along with the transgo shift kit. And I have a couple questions about the torque converter to tranny seal. Ok, i've already replaced the driveshaft main seal (between the tranny tail and the...
  7. R

    Trans Woes...

    My trque converter had the shudder, im currentlly replacing it now with a 3k red line torque converter. Normally the shudder for our torque converter happens when your in early third gear, and last for two second.
  8. R

    Rear main seal (transmission - driveshaft seal)

    Is a tool needed to remove and install this seal, or can it just be done. What about the tps sensor on the drivers side on the transmission.
  9. R

    installing 2 rings on FWD clutch (included in transgo AODE shift kit)

    question for the one's that have installed a transgo shift kit: there are 2 rings, not sure what type of material they are made of, that are included in transgo's reprograming kit, they supposelly go on the FWD clutch, getting to that FWD clutch is that hard to dissasemble from the trans, and...
  10. R

    My dash clock died

    Mines to, it deems really dark when I got my headlamps on, and even with them off, it flashes on/off. I think they are just poorly made.
  11. R

    Transmission cooler

    Im putting a tru-cool 20,500 gvw in mines, instructions say place it infront of both the radiator and a/c cooler (unsure if it's the a/c cooler but it's visible looking from the front bumper).
  12. R

    Transgo shift kit

    Im almost done installing mine. Mine's came with the video in a black box, and was featured on an sccoa.com/articles/transgo.html article, although it doesn't say HD2 on it im assuming it's the same thing hence the instructions say the same thing an hd2 can do and perform. Pretty straight up...
  13. R

    transgo shift kit owners, I need intructions

    Any of you guys still have your HD-2 manual instructions? specifically I need the instructions on the 3-4 accumulator piston and springs install diagram. My manual shows only 1 spring in between the accumulator and retainer. Shoulnt their be another between the trans and the 3-4...
  14. R

    Torque conver - flexplate bolts, what grade?

    I purchased a 3k stall torque converter over the weekend from red line converters. It din't come with any bolts, but I know the 3/8 24 fine thread bolts fit perfectlly, the only problem is that I can't find them in a grade 8 type (coarse thread yes, not fine threaded). Will grade 5 do? Or am...
  15. R

    Removing tranny. Help

    For those using aftermarket torque converters. Are grade 5 bolts good enough to bolt the torque converter to the fly wheel, I purchased a torque converter with a stall of 3k? the only bolt the fit into the TC threads are the 3/8 24 fine threaded bolts. The grade 8's aren't available in fine...
  16. R

    AODE transmission oil, is it clean?

    phew, I thought id might have to go through a rebuild. I've got a new Torque converter (3k) stall speed from red line torque converters, got the 20,500 gvw trans cooler, and the shift kit all going in possibly saturday maybe sunday.
  17. R

    AODE transmission oil, is it clean?

    I checked the transmission oil dip stick to see the color of the oil, and as usual it was redish clean. But when I took the Metric trans oil pan out to install the transgo shift kit, the valve body part towards the pan was dirty, with a muddy film. So my question is: How worried should I be...
  18. R

    Removing tranny. Help

    Yeah I purchased a trans jack the other day, even using that for support i've managed to pull just a little (maybe an inch) but it still wont budge, i'll try the scredriver method.
  19. R

    Removing tranny. Help

    Thanks STR8, I took 4 of the bolts out fro fly/Torque converter, there doesn't seem to be any more bolts I can pull, but I still can't get the tranny out. I'll try again tomorrow. I took all the bolts out from the bell house to the ones attached to the cylinder heads. But holding the crank was...
  20. R

    Removing tranny. Help

    Holding the crank bolt from in fron of the engine? where the pulley's are?
Top Bottom
Back
Forums
Menu