Search results

  1. O

    V-8 conversion

    Having a V-8 parts car is the best way to go --Hands down-- All the little stuff that you would never think of will be there.
  2. O

    5 lug conversion

    If it doesn't cost to much you may want to take the emergency brake handle set up. if you ever go to disc in the rear it will save you the hassle of modifying yours. If there cheap take the cables and brackets also. just a thought
  3. O

    Fuel Line Thread Size Help

    can you post a picture?
  4. O

    160 MPH SSP gauge question..

    i just sold a bbk 180 mph on ebay it brought $160
  5. O

    85 swap using sn95

    I'm running almost all SN-95 stuff on my 91 the 95 is a great year for the spindles they don't stick out so far as the newer ones. and the brakes work out great also. Not sure about the engine stuff i think that's a little different The complete rear end will go right in and yes it is a...
  6. O

    five lug rear brake drums?

    I got ranger drums also
  7. O

    HELP! I CANT SEEM TO TURN HER ON ANYMORE:-)

    might try a small shot of starting fluid and see if it pops off a sec. Then you will know if it is spark or fuel for sure. --very small shot--or even use carb cleaner If you got spark fuel and compression in the hole something's going to happen
  8. O

    where to hook up the tach? Mallory and MSD stuff

    Hi, I'm gathering stuff up for my fox and I may have ran into a slight snag. I'm going to run a supercharger with a carburettor set up I'm going to run a Mallory distributor with a blaster coil and a series 6 MSD-BTM box to pull back the timing when under boost I would like to keep the stock...
  9. O

    I'm looking for the tach wire

    Hi, I'm changing over to an old school blower with a carb and I would like to keep factory tach working. I will be running a Mallory distributor with a blaster coil and a MSD 6-BTM box. I'm hoping to hook in at the -side of the coil. anyone know right off where I can pick up the tach wire? I...
  10. O

    87 gt whats it worth

    May I offer a tip? I buy cars for just about everyone in my family so I have bought a few. When I decide to buy a car and I know what I want to pay I make a real offer. I hand them cash and say, "count this,, Then I got a question for you" It's hard to hand the money back after they play with...
  11. O

    Starting Engine For The First Time

    Go to a boat place they use it for all kinds of stuff
  12. O

    fox body trans trouble

    My clutch was really hard to push down. I pulled the cable out and checked it and it seemed to move freely. I went ahead and replaced it since it was out and I had the new one. Then it was a lot easier to push. Maybe they only bind under a load? Might be worth a try if the cable looks old.
  13. O

    347 Shortblock with flywheel and balancer

    Location?
  14. O

    V-8 and 4 cylinder proportioning valve-- the same fittings?

    I'm getting ready to change the booster and master cylinder over to SN-95 stuff and Mustang 5L5 suggested that I call maxium motorsports to get the conversion lines to make the job easier (Thank you 5L5) When I called the guy was very help full. But what he didn't know was weather or not there...
  15. O

    Does this booster look right?

    so pattern on a fox has the one bolt hole closer like the booster shown?
  16. O

    Does this booster look right?

    Hi guys, Today my power booster came in at auto zone. Does this bolt up pattern look right? I got the 93 Cobra booster to keep from having to elongate the holes. Some where on here I saw a picture of a fox fire wall with out the booster.--I can't find it now. Looking at it from the bolt...
  17. O

    Sn-95 Master cylinder on a fox questions

    Hi, looked at the stickers and didn't see an answer to this question unless I missed it. A year ago I switched over to 5 lug disc brakes on my fox and ran the original booster and Master cylinder. Now I'm paying for that mistake. The rear pads are gone and the fronts still look good. "I...
  18. O

    Home made logo floor mats

    yes they were iron on. I was afraid that the cheap carpet on the mats would melt from the heat.
  19. O

    Home made logo floor mats

    No it's straight. I don't know why it looks that way in the picture, It's straight I measured it a few times before I clamped it. Might be the curve of the mat. It dose look crooked in the picture tho,,
  20. O

    Home made logo floor mats

Top Bottom
Back
Forums
Menu