Search results

  1. 98bluevert

    Cheapest place to get MM XL subframe connectors???

    Also if anyone has any pics as to where they all need to be welded would be great, or i'll get ahold of MM to see what they say.
  2. 98bluevert

    Cheapest place to get MM XL subframe connectors???

    thanks for all the info. i'll have to check out that website. As far as installing goes, i work in a body shop so i'll install them there after work one night.
  3. 98bluevert

    Cheapest place to get MM XL subframe connectors???

    ok i tried to do a seach but came up empty, where would the cheapest place be to get Maximum Motorsports XL full length subframe connectors for a 98 convertible.
  4. 98bluevert

    Winter driving: How much weight should I put in the trunk?

    Not sure as to why having 2 cars is not possible right now for ya, why can't u go rent a storage unit, put your stang in there, and then go find a pos old chevy s-10 which are a dime a dozen.
  5. 98bluevert

    VIN # Decoder

    i thought all 97 and older stangs had mechanical speedos where u can't use a spedcal.
  6. 98bluevert

    AC not working neither is cooling fan.

    ya if u looked at the new pics i don't have that problem anymore, i have 12.xx volts in the red/orange wire and the ground has little to no resistance in it. If i jump the fan prongs the fan works put when i plug in the fan connector it doesn't. anyone know what it might be.
  7. 98bluevert

    AC not working neither is cooling fan.

    Ok sorry to bring this back up but i just now got time to work on my car since i got my new garage. Still having the same problem and here are some more detailed pics of what i am getting at the cooling fan connector. http://pg.photos.yahoo.com/ph/figgy_1984/album?.dir=/b81dre2 if i jump...
  8. 98bluevert

    HELP!!! Got a clunk in the rear

    well this is no little clunk, this is more like a noise when a u-joint is going out, right before it goes. i checked to make sure it wasn't the u joints, i know its something in the rear end itself. since i had 4.10 put in it with all the bearing also changed could it be possible that the...
  9. 98bluevert

    Degreaser + Paint = no bueno

    At least it wasn't your car u learned on
  10. 98bluevert

    HELP!!! Got a clunk in the rear

    ok i was reading on some past post and someone said that they replaced all there seals and bearings and after 400 miles had to reshim the rearend because the bearings had seated more. could mine need reshimmed or am i looking in the wrong direction here
  11. 98bluevert

    HELP!!! Got a clunk in the rear

    When i release the clutch i here a clunk from the rear end. i had 4.10's installed a couple years back and have maybe 7,000 miles on them. i had all the bearings and seals replaced. i don't know alot about rearends but could all my bearing have seated and my rear end need reshimmed. I jacked...
  12. 98bluevert

    Degreaser + Paint = no bueno

    congrats, glad it didn't screw up your paint, since u have a buffer i am assuming its an actual buffer, not an orbital polisher, and u know how to use it. But anyways just remember to stay away from the edges, u burn through and that will be more than an 8 dollar fix.
  13. 98bluevert

    Moved my spoiler back

    I'm in the paint business and agree with him. Wash it with soap and water first. then get some rubbing compound and take it to it lightly with a soft cloth. 3M makes some good stuff. go to NAPA or Carquest or someplace like that tell them what you need it for and they will help you. Make sure...
  14. 98bluevert

    Question about cams

    ok did a search and finally found this by DropTopPony and TGJ So if i get aftermarket PI cams like COMP or VT's then will they work with nPI heads with offset retainers? Also if i get the 262ah or stage 1 do the springs have to be upgraded? Anyone with more info please chime in.
  15. 98bluevert

    Throw out bearing? Help

    why was the throwout bearing not replaced when the clutch was replaced?
  16. 98bluevert

    Question about cams

    i know if i go with stage 2's i need springs but since my stock lift is like .473 i didn't know if i could use something like .550
  17. 98bluevert

    Question about cams

    how high of a lift cam will a stock nPI motor handle without PTV issues. also would i have to get new springs.
  18. 98bluevert

    good article on pi swaps

    i have a good link but its on another site and won't let me post it. get ahold of me
  19. 98bluevert

    good article on pi swaps

    i'd say yes to that. your raising your compression, airflow and hp. anytime you do that you should get a tune
  20. 98bluevert

    Throw out bearing? Help

    take the longtubes off yourself then go in there even if u have to haul your car in. you'll save 6-8 hours of labor there. But i would do the work myself and replace the clutch at the same time.
Top Bottom
Back
Forums
Menu