Search results

  1. Yellow302

    Possible Bad Rear Spring Or Springs?????

    They are flat the same as mine, under the rear spring install guide, I remember them telling you to point the pig tail a certain way on each of the LCA before compressing it back into the car. Or else the car will be higher or lower on one of the sides. The front springs have a grove cut into...
  2. Yellow302

    Possible Bad Rear Spring Or Springs?????

    Im going to look at the design on the LCA's for you...
  3. Yellow302

    Possible Bad Rear Spring Or Springs?????

    Check the lower control arms, maybe a bolt is snapped. It may look like it is in place... I would check them. Also make sure the pig tails are facing the correct way on the rear LCA's tey can make the car slanted if not put on correctly.
  4. Yellow302

    Possible Bad Rear Spring Or Springs?????

    I was in a similar situation. Car accident, frame machine and the guy couldn't get it right for some reason. 2 years later I find out that the front spring was broken and never replaced. Fast forward to now. The car was leaning to the left, One of the rear struts was blown and leaked out...
  5. Yellow302

    Pbr Brake Upgrade, Time To Replace Rotors And Pads

    I cannot for the life of me remember what I did to upgrade all of my brakes. I bought a kit PBR that is like the 99+ cars or I bought the dual piston cobra kit. I don't know what is what. But it is time to replace the rotors and pads. I do remember needing to have 17" wheels from now on...
  6. Yellow302

    Center Cap Replacement - Y2k Cobra Snake Emblem 2.5 Inch

    I believe the center caps are 2.5 inch. I have a set of 17 by 9 y2k cobra rims. One of the center caps got scuffed up and I would like to replace it. I am also open to a set of red R cobra decals to cover all three but the size they sell them is 2 1/4 Has anybody used these instead of paying...
  7. Yellow302

    HVAC lights not longer coming on after LED upgrade

    Yeah If should be a piece of cake, I'm not sure what bulb to order for it because I've changed the shifter to a 99+ model with the OD button on the side. I have to take it apart and pick white or blue.
  8. Yellow302

    HVAC lights not longer coming on after LED upgrade

    Problem solved. The bulbs were too fat to get in the hole fully. I removed the black cover peice, widend the holes so the bulbs could go deaper. I also have a peice of white plastic break that acts as the hold down when you turn the bulb into the right. A little super glue fixed that. In...
  9. Yellow302

    Volt Meter Bouncing - Chasing an electrical issue

    4-12-2013 Just adding my similar issue. I had oil driping into my alternator (relocated for the supercharger) Fixed the oil leak. Installed new altenator. Removed drivers side ground wire. Found it to be loose. Reinstalled ground wire on the back of the altenator hosing and connected it to the...
  10. Yellow302

    HVAC lights not longer coming on after LED upgrade

    the controls work, the dash is fine. Just the two bulbs behind the HVAC plate are not comming on. 17, 13, or 6 all have something to do with that area, I will check them all. Worst case I'll tear it appart and try the old bulbs, one of them was still working. Thank you for the diagram!
  11. Yellow302

    HVAC lights not longer coming on after LED upgrade

    Title says it all, I have converted to hyper white LED's. The dash was no problem. HVAC lights are just out. I double checked the plugs that go into the back of the plate, still nothing. Is there a fuse that may have popped?
  12. Yellow302

    Heater tubes were leaking, now fixed.

    I knew how rare these were and no replacements are made for our cars. I spotted one on ebay and purchased it right away. Glad you were able to repair yours.
  13. Yellow302

    Low Voltage, belt slipping? What other causes?

    I did have to replace the headlight lamp switch and wiring. I was very carefull and used solder and heatshrink tube. I could look for this group wire under the dash. Can you point me in the right direction? Under the dash, behind the cluster guage? I have a brand new multi meter guage which...
  14. Yellow302

    Low Voltage, belt slipping? What other causes?

    Just as the title says. I am getting a bad hum or buss through the speakers. I recall a grey connector by the coil being involved with this? Correct me if I am wrong. Would like to get rid of the annoyance. Thanks!
  15. Yellow302

    Low Voltage, belt slipping? What other causes?

    It will be an easy fix. just undo clamp, slide hose down, tighten clamp. Job complete. Just incase of any spillage I can throw a plastic bag over the atl. Its just so damn cold to do any work this time of year, it sucks!
  16. Yellow302

    Low Voltage, belt slipping? What other causes?

    Tested out everything, everything looks ok. Worked for about 5 min while driving perfect, I mean dead center fan on lights on radio on. Problem, I have a paxton novi 2000, so the altenator is relocated to the bottom left of the car. There is an Oil drain that goes from the super charger into...
  17. Yellow302

    Low Voltage, belt slipping? What other causes?

    I can use a baby screw driver to clean it up. I will also do the full testing over xmas break. I found the proper steps to test and replace if need be. I will also have to check ground wires as well (even though they are new)
  18. Yellow302

    Low Voltage, belt slipping? What other causes?

    Update 12-8-2012 I installed a new belt. (fixed my squeak problem) Replaced fuses. I used alot of di electric grease when I installed/replaced the fuse. - Could using too much cause a lack of connection? During my replacement of the fuses I used electric cleaner and fresh fuses. The problem...
  19. Yellow302

    Low Voltage, belt slipping? What other causes?

    Im with you on that. It just sucks because it was a brand new altenator.
  20. Yellow302

    Low Voltage, belt slipping? What other causes?

    12-2-2012 So the belt I got was way to small. 87 inches. The one I had on there was 95 inches. I bought a 94 inch and having it delivered. Update on symptoms. The voltage is bouncing cold and at any rpm now. This should narrow my issue down to the voltage regulator on the altenator and or...
Top Bottom
Back
Forums
Menu