Search results

  1. lightblade

    Suspension Noise

    +1 for sway bar endlinks, i had the same problem and found the upper bolt for the swaybar endlink was loose and was causing my popping, clunk noise.
  2. lightblade

    Raptor Performance shiftlight install

    ABout $120, used some electrical tape and additional wire, also some silicon sealant around the hole i drilled through the firewall. Took about 2 hours to install from start to finish including figuring out the best way to mount it in the hole after i had the dash part lol
  3. lightblade

    Raptor Performance shiftlight install

    So I was looking around inside the car to see where I wanted to install my shiftlight, and bam it hit me. I never use the 12v power source on the dash above the radio so I decided to install it there. I like it so far, very clean and stealthy. PICS!
  4. lightblade

    Post pics of atermarket tailights installed

    Hey, I'm looking to go with some aftermarket tailights, I have seen a few I like but not of them installed on a stang, so go ahead, post your pics!
  5. lightblade

    GT500 Lip installation on a GT

    It looks great, nice job!
  6. lightblade

    Motor Mounts

    I got a set of prothane billet aluminum motormounts off ebay for 99$ might as well if u plan on building up the motor, i have seen no drawbacks to them so far.
  7. lightblade

    GT500 Lip installation on a GT

    Same thing happened to mw with my lower grill when i first painted it, i got some rubber polymer flat black spray paint that is used in truck bed liners and it is working fine and withstanding the sand and road debris is a tuffer more flexable paint, i got it at autozone i tihnk, cheaper then...
  8. lightblade

    GT500 Lip installation on a GT

    I think the GT500 lip would be a nice finishing touch to the front end of car, what do u think? Can you order them from ford online for that cheap if so where?
  9. lightblade

    GT500 Lip installation on a GT

    Where did u get that lower grill??
  10. lightblade

    Anyone got any pics of a grabber orange convertible?

    PICS! :nice:
  11. lightblade

    Convertible Light Bar

    I have the MRT 2-Tone, absolutely love it, here are some pics and a link to a install write up:nice: http://www.grabberorange.net/forums/viewtopic.php?t=502
  12. lightblade

    Its Painted!! (pics enclosed)

    I went with the chrome layover grill and painted them black, did both upper and lower for under 100$, gota love ebay lol
  13. lightblade

    Finally, pictures!

    I think some clear/black turn signal/parking lights would go good with those headlights, they are similar to mine.
  14. lightblade

    8-bolt flywheel with a 07 GT clutch?

    Nope, cast iron crank 6-bolt. I thought it was 11'' but all the after market twin disc clutches are 10.5 witch i will get and aluminum 8-bolt flywheel to go with eventually, but for now I want to run the stock clutch and 8-bolt cobra flywheel.
  15. lightblade

    8-bolt flywheel with a 07 GT clutch?

    I'm puting a forged cobra crank(01) in my 07 GT. The new crank is 8-bolt so it wont work with the stock 6-bolt gt flywheel. My question is will a 01,03,04 stock cobra 8-bolt flywheel work with a 10.5 inch stock 07 GT clutch? I'm thinkin it will, but want to be 100% sure before i buy a new...
  16. lightblade

    One pic of the new wheels on the car...

    Can't go wrong with black wheels on a grabber orange stang. Also love the machined lip just like the ones I have.:nice:
  17. lightblade

    Old Clutch removal has begun...

    Im looking to upgrade my fuel rails for my engine buildup, which ones did you go with and where did u get them?
  18. lightblade

    most RWHP shelby GT (not a 500)??

    My 07 Gt came with 3.55 gears, and a demolet cai and sct xcal-2 tune got me 30rwhp for only $500. This mod alone makes more power than the Shelby GT My suspension( bilstein shocks/struts, ford k-springs, maximum motorsports caster/camber plates, billet aluminum lower control arms with...
  19. lightblade

    295/35/18..........Can it..

    I have 18x9 all the way around with a 265 up front and 285 in the back, no problems. :nice:
  20. lightblade

    Finished my christmas present mods, pics!

    I believe they are the halo 2 projectors, made by jdm, got them on ebay
View older results
Top Bottom
Back
Forums
Menu