Search results

  1. BADPONYsc

    Changing all 6 lights tomorrow at 5:30am, what is the easiest way?

    There's no need for racist comments. :D Hehehe, j/k
  2. BADPONYsc

    loud fuel pump

    Almost two years ago now, my pump started to get louder and the pitch kind of waivered up and down a little.... not a constant tone. Well, of course it died on me while I was out of town. Riding down the road, all of the sudden the car starts slowing down. I pull over on the side of the...
  3. BADPONYsc

    door lock actuators install?

    I'm confused... you're saying there's no plastic mounting bracket holding the actuator to the inside of the door? Did your car have power windows already? If so, what happened to the bracket? The actuator won't work without being mounted to the door with the bracket. Did the power lock...
  4. BADPONYsc

    Manual Steering Rack

    I've heard of that being done, but I went with the Flaming River anyway because I didn't want to end up needing unexpected parts at the last minute. All that's in the Flaming River kit though, is the rack, shaft, and tie rod ends. I've heard going the auto-store route is alot cheaper than...
  5. BADPONYsc

    Eibach Drag-Launch Springs....

    I have the drag launch kit and it rides fine on the street. Not much different than stock really. The rear is lower than stock by just a tad, but the front is WAY higher than stock. I can only fit one finger in the rear gap (between tire and fender) but four fingers in the front. I have a...
  6. BADPONYsc

    Whats this?

    I think it's for the power door locks. Take it off and check and see if the door locks quit working. I left mine off one time and my locks didn't work, found later that I had left that off. If that is what's draining the battery, I can't think of why... except maybe one of the lock...
  7. BADPONYsc

    weld draglite skinnies

    I used spacers for a while when I first got them, then later I just grinded down the spot where they rubbed.
  8. BADPONYsc

    Front bumper cover 88GT

    Oh, ok... yeah the main bumper is just 4 big bolts, but the cover will have to come off to do it. Removing the bumper cover isn't that hard really though. I've done it several times. First thing is that you'll have to remove all six lights...headlights, corners, inners. Then there are...
  9. BADPONYsc

    Back Lower Than Front

    I have the Eibach "drag-launch" kit and it's the same way but worse. The rear is a little lower than stock and the front is a good 2" higher. I've been told that's the way this kit should be, for weight transfer... although Eibach doesn't mention the height difference anywhere. I may end up...
  10. BADPONYsc

    Front bumper cover 88GT

    You mean you're foglight reinforcment is off and you're tring to put it back on? I put mine back on with the bumper cover on. It's kind of awkward laying down and getting up in there, but it's do-able. It shouldn't be nessesary to remove the bumper cover to install it. Or do you mean that...
  11. BADPONYsc

    Quarter window removal question

    I took mine out of my old (wrecked) car a couple of months ago. The rubber molding is attached to the glass. The window and molding comes out all in one piece. You have to remove the inside plastic quarter panel trim.... the big pieces that have the rear armrests in them. You may not have...
  12. BADPONYsc

    Manual rack

    I've heard of people just getting a standard auto-store replacement for the manual rack. You'd need the manual rack, shaft, and tie rod ends. I think it's a good bit cheaper than the Flaming River one, but I got the FR just to make sure everything was included and there would be no suprises...
  13. BADPONYsc

    battery relocation

    Yeah, to be NHRA legal you would need to hook the ignition system to the solonoid (relay) and then run the main battery + wire from the solonoid back to the switch and then from the switch to the battery. Also you would need to run the alternator's charge wire back to the switch also. Then the...
  14. BADPONYsc

    Anyone know where to get BBK CAI replacement parts?

    I have the BBK CAI also and I have the splitting connectors too. Not bad enough to cause leaks yet, bet they are splitting... mostly from being taken on and off over and over. I had this kit on my old GT and on my new LX and on both cars, I had to hammer a spot on the strut tower because of...
  15. BADPONYsc

    Electrical help

    I know this is obvious, but..... a blown fuse? The fuse for the dash lights is #4 (15a). It sounds like it may have shorted out somewhere, in which case you'd have to either hunt the short down, or run a new power source to the switch. I don't know, I'm just guessing. Good luck with it!
  16. BADPONYsc

    Belt squeeks pretty loud on intial startup....

    3G Alternators come with a pre-installed underdrive pully, or a pully that's smaller than the stock one, anyway. Compare them, you'll see. This could make the belt a little looser and could be causing your slipping problem. A slightly shorter belt should help. That, or your tensioner may...
  17. BADPONYsc

    sunroof help [picture inside]

    Aw man, sorry. I sold the sunroof awhile ago. Have you tried Mustang Parts Specialties. Even if they don't have it on the site, I bet you could call them and get it. They buy wrecked mustangs and part them out. Here'e the site.... http://www.stangparts.com/
  18. BADPONYsc

    sunroof help [picture inside]

    My wrecked 90' GT had a sunroof and I don't recognize that part. I sold the sunroof its'self but still have the parts that were connected to the roof. I'll look out in the garage and see if I have something that looks like that. Was that piece connected to the sunroof or to the roof? If...
  19. BADPONYsc

    Flowmaster Part # Check

    If you use 2.5" mufflers with 2.25" tubing, what most shops are going to want to do is just slip the tubes into the mufflers and fill in the difference with weld. This will work, but it will be ugly looking. The alternative would be to remove the flowtubes from the H-pipe, remove the...
  20. BADPONYsc

    Fuel tank dropping problem

    Man, I feel for you. I've changed mine out a couple of times with the help of a mechanic friend of mine who knows what he's doing and a lift. Also it was summer, so that made it even better. I wouldn't want to do it by myself. Seems like fishing the old pump out and fishing the new one...
Top Bottom
Back
Forums
Menu