Search results

  1. Bill88Stang

    Hp Estimate With Combo

    Yes I know I wasn't expecting a rocket ship a lot of it I already had its better then being all stock though . I was jus looking at opinions I know it's on the small side
  2. Bill88Stang

    Hp Estimate With Combo

    Yea that's why I mentioned the different injector , cam, throttle body , maf combo to change it with .
  3. Bill88Stang

    Hp Estimate With Combo

    Just curious what you all would estimate my power out with my combo..10.5:1 351w stock crank and rods, rods bushed for full floating Pistons, arp hardware.heavily ported world Windsor Jr heads 1.94 1.60 valves matched to 1262 intake and 1450 exhaust gaskets. Comp pro magnum 1.6 stud mount roller...
  4. Bill88Stang

    F303 Cam With A 2500 Stall

    Yea I was hoping it would work ok... I know it's not the best for the set up but I think it will be better then the e303
  5. Bill88Stang

    F303 Cam With A 2500 Stall

    Not like if I was running it with a stock 1800 stall
  6. Bill88Stang

    F303 Cam With A 2500 Stall

    So it wouldn't be too far off
  7. Bill88Stang

    F303 Cam With A 2500 Stall

    4.10's I have a big trans cooler and 30 inch tires which are stock on the Lightning
  8. Bill88Stang

    F303 Cam With A 2500 Stall

    I believe the f is 2800-6000 in a 302 so the extra cubic inches in the 351 might make it about 2500 and up which would be perfect
  9. Bill88Stang

    F303 Cam With A 2500 Stall

    I don't think the 2500 stall will be too small for it either . I'm thinking the f should make a little more power and pull harder
  10. Bill88Stang

    F303 Cam With A 2500 Stall

    I know there are better cams I'm just saying comparing the e to the f the f would make more power in my set up that's all
  11. Bill88Stang

    F303 Cam With A 2500 Stall

    Not exactly mustang related but I hope you can help. I'm wondering if a 2500 stall converter would be enough for a f303. It would be in a 94 lighting with a10:1 351 mass add converted running a mustang a9p computer. It currently has a e303 with a 1800 stall and I have the tranny out replacing...
  12. Bill88Stang

    B303 Or E303 With This Combo. No Flames Please

    88 notch stock bottom end 302 in great shape. 3 bar gt40's milled .030. 1.7 roller rockers. gt40 tubular upper and lower 75mm throttle body 24lb injectors, c&l 76mm mass air housing. 255 lph fuel pump. t5 with 3.73's. car currently has e303 but wanted to go to a b303 i had laying around. thanks!
  13. Bill88Stang

    88 Notch Not Charging

    The 88 notch I recently got is not charging, has the stock alternator and I don't have any wiring diagrams for it what wore on the back do I check to see if I have battery voltage to so I know if the alternator is just no good or if it's something else? Also I noticed the dash is pretty much...
  14. Bill88Stang

    Outside Door Handle Broken How Do I Get In

    i just picked it up two weeks. ago its a project that the previous owner didnt finish. it stays at my house im on 2 and a alf acres thats all fenced in and locked when i go and come. ive been in and out of that car a total of like 3 times so far, been under teh hood trying to straighten out what...
  15. Bill88Stang

    Outside Door Handle Broken How Do I Get In

    R/F door does not open from the outside only the inside, seems to have a door lock actuator thats all binded up. drivers door had a broken outside door handle, but if you pullon it just right at the right corner it would open until i went to get in it last night and it all popped off, i can see...
  16. Bill88Stang

    My Combo Estimate

    recenetly picked up this 88 notch that was orignally a 4cyl but the previous owner took everythign from a 92 car to swap over, motor trans rear wiring and computer. just curious of waht everyone thinks of the combo im not expecting muhc would would like a estimate on what it might make. stock...
  17. Bill88Stang

    Engine Broken Idle Speed Adjustement Screw

    when attemtping to raise the idle speed the bolt head broke off the throttle body and now i cannot get the car to idle higher for the cam. it has some rust so unfortunately the rest of the screw might night be able to be moved in or out as ive tried remove throttle body before and its just about...
  18. Bill88Stang

    Help me create the "Surging Idle Checklist"

    does any one have a good picture regarding opening up the port on the iac with a dremel to allow engine to idle higher? it was mentioned in the very beginning of the post.
  19. Bill88Stang

    Trick Flow Intake Install Instructions Help Needed

    Well I was asking about the vacuum line routing for that intake since I don't believe they have it hooked right. Example is the PCv does not go to a vacuum port in the back like stock , it runs directly into a small t where the line from the vent on passenger valve cover that goes up to the...
  20. Bill88Stang

    Trick Flow Intake Install Instructions Help Needed

    The coupe I recently picked up idles horrible and is pretty rich at idle. The previous owner installed a trick flow intake on it, not sure if track heat or street heat I'm not sure if you can tell by looking but I'm wondering if anyone has any install instructions especially how vacuum lines are...
Top Bottom
Back
Forums
Menu