Search results

  1. Numbles

    Replacing K member.

    Tko's require a fox style bellhousing because of the length of the imput shaft. So even if you have a sn95 you need the fox bellhousing. And the only think I enxerienced with my tko and the shifter is that is was moved 1 inch to the right in the transmission tunnel. Compared to the t-5...
  2. Numbles

    Lower control arm Bolts?

    FWIW. The previous owner of my car had grade 5 bolts in for that rear control arms. The car has been launched on slicks countless times. Havent had a problem.
  3. Numbles

    Best way to get rid of bumpsteer?

    Get a bump steer kit. upr/mm/ every other mustang company practically sells them. Sucks though. You will have to get an alignment done again after they are installed.
  4. Numbles

    Can I run MT ET Streets w/o a tube?

    You can run them without tubes. But do a search. This topic has been debated bofore.
  5. Numbles

    I know its a longshot but.... (LT / xpipe q)

    Go to a muffler shop and have it done. They can probably give you a price for making a custom h-pipe and installing your catback for the same price of a h-pipe from any of the mentioned companies.
  6. Numbles

    Lower control arm Bolts?

    Went to lowes and they had the bolts. 5/8ths x 5 inches. And bolts and washers. Everywhere else only has up to 1/2 inch in grade 8 hardware.
  7. Numbles

    Rearend brake line pics anyone?

    I got my front lines from maximum motorsports. The rear line is from discbrakesrus in the ford, mantang and gt section. It is listed by itself and its the only one. I think its for 87 to 04 stangs.
  8. Numbles

    Lower control arm Bolts?

    Never heard of greens. Are they a shop or website?
  9. Numbles

    Rearend brake line pics anyone?

    Cool thanks. I just remember the line having a banjo fitting on that side. And the pictures on their site also have banjo fittings on that end so it threw me off. And it also comes with crush washers for a banjo bolt.
  10. Numbles

    5 lug conversion problem

    In the process of doing the same thing. Eye it so you can drive the car and then drive to the closest alignment shop.
  11. Numbles

    Rearend brake line pics anyone?

    Im just finishing up my 5-lug swap and need a picture of the rear center brake line. They one that goes from the body to the rear end. Reason being, The braided one I got from discbrakesrus isn't like the factory one. It comes with the distribution block for the rearend hard lines on one...
  12. Numbles

    Lower control arm Bolts?

    Ill think Im going to cancel my order with 50resto and go to lowes tomorrow. Seems to me I remember their bolt selection and it was huge.
  13. Numbles

    Lower control arm Bolts?

    I already got the MMR tubular control arms and coilovers. They had a deal for $300 for both. I needed new balljoints and upgraded in the process. I also just got cc plates as well. Did you just hammer those old bolts out. My sawzaw is no match for those bolts. Ill try a new bit although I...
  14. Numbles

    Lower control arm Bolts?

    Anyone know where to get front lower control arm bolts. In the process of changing the front suspension I found that the right side bolts were rusted to the bushing sleeve. And I cant find anyone thats sells these bolts. Because I need to source them before I take out the sawzaw and cut the...
  15. Numbles

    Who here autox's.

    Vib. I heard and this is purly a "I heard" thing. That they were only able to perform as good as stock shocks when it came to cornering. But with over 10 years of wear and tear on my suspension. I think they will do fine. Especially since they are ajustable. For the proce I got them I couldn't...
  16. Numbles

    Who here autox's.

    Just picked up my strange ajustables. Got an amazing deal on them. You can definately tell the difference in the 10 settings just by hand. On the stiffest setting you cant really even move the shaft. So I think they will work good. But on another note. Going to various 1/4 strips around...
  17. Numbles

    Who here autox's.

    Hangman. What tires are you running. Good pic of your car btw in the my garage link.
  18. Numbles

    will it handle a 75shot?

    Should be fine with a 75 or 100 shot. Just get it tuned if possible.
  19. Numbles

    3>2 port master cylinder conversion kits

    I just ordered the MM kit. As far as quality goes, its just a few fittings and a hard line. I dont think you can go wrong with either. Get whichever one is cheaper. Dan
  20. Numbles

    Who here autox's.

    And can I just buy the 87-93 models with sn95 spindles. If I remember right the only difference is the height difference.
Top Bottom
Back
Forums
Menu