Search results

  1. twotonefreak

    What kinda heads is this GT-40P or ......???

    I would go for it, if you have any doubts about them, run 'em down to your local machine shop and have them checked out for any leaks, cracks, or warpage.
  2. twotonefreak

    What kinda heads is this GT-40P or ......???

    I don't think any Cobra's ever came with the P's just the Explorers. There aren't any emissions hook ups on the back of the heads are there?
  3. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    Mine was on an Dynojet.
  4. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    Yea I am curious to see how much it picks up with the new parts and also when I finally add a larger mass air and a t-body.
  5. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    Hmm, well I think I hopefully found a reason for my low numbers, mine has had a valvetrain noise since I built this engine and I took it apart and found several bent/tweaked push rods, some very funky wear on the stocker rockers, and the "supposed" correct springs that the local machine shop...
  6. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    Thanks, I was just curious about that.
  7. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    I don't expect big gains until I get a larger MAF on there, but I will def. let you know what happens, also tell us what P.A says after you talk with them. Also how does your's drive down below 2500rpms? Mine still has a slight surging, but has gotten a lot better as the EEC has learned it.
  8. twotonefreak

    Dynoed my GT40P setup,kinda disappointed

    Hey man I feel you on the low dyno numbers. Combo in sig. I only did 239rwhp and 272lb/ft on a dynojet through a T-5. My P's are stone stock though, just rebuilt. I still have a stock T-Body and MAF and valvetrain. I am going to be adding my new 1.6rr, 6.450 Comp pushrods and Lunati...
  9. twotonefreak

    Roller rockers with stud conversion kit

    I was looking at my stockers compared to those off a 94 Cobra I was helping to do a cam swap on, and there was no difference between the two except one said Cobra?? I am gonna maybe massage or remove the baffle on the RH cover and see what happens, but I have a set of tall chrome :nonono...
  10. twotonefreak

    Roller rockers with stud conversion kit

    Will they clear Foxbody valve covers?
  11. twotonefreak

    Roller rockers with stud conversion kit

    Hey guys I am gonna install my 1.6 Roller rockers (they are stud mounted) and I also picked up a conversion kit. My question is, will these rockers with the kit clear my stock valve covers? I have heard many say roller rockers won't and other that say they will? :nice:
  12. twotonefreak

    GT-40P Heads, which motorcraft plugs?

    They are 32s. AGSF32FM to be exact. I work in the local Ford parts department. But I was just wanting a recommendation on wether I should go colder or hotter? Sorry about that I should have worded it differently :nice:
  13. twotonefreak

    GT-40P Heads, which motorcraft plugs?

    Hey guys need a quick recommendation for which motorcraft plugs and a recommendation for the gap for my P heads. As far as the ignition goes, I have a Blaster coil, Accell 8mm wires and Accel cap and rotor.
  14. twotonefreak

    Loud And Good Flowing Exhaust?

    I don't have to worry about emissions here in ARK, but I have Hedman LT's O/R X-pipe, Spintech Prostreets, 2-1/2" tails w/ 3-1/2" tips and talk about loud, its nice and quiet, just a slight rumble in the cabin, but holy **** its loud outside.
  15. twotonefreak

    Has anyone ever been tempted? be honest....

    Tempted yes, did well not actually I bought a sweet 97 T-top Z28 (LT1) and owned it for a couple months, I had a few mild mods on it, but nothing serious, it was a quick car, I just couldn't ever get comfortable while driving, I think it was b/c my poor 94 GT was just sitting at home w/out a...
  16. twotonefreak

    WTB 73,76 MAF for 19#inj.

    Hey guys just wondering if any of you have a larger maf for 19#injectors? I don't care if it is a C&L or Pro M. Let me know thanx :flag:
  17. twotonefreak

    GT-40P head combo....Spark plug issues????

    On my 94 I used standard (foxbody) LTs on my 94, but I reworked the number 3 tube on the driver's side(used some header tubing from Shoenfield, they are located here) and cut and welded in a bend to work, also on my friends 88 GT w/ P's we used his Mac shorties that he has had for a couple years...
  18. twotonefreak

    Those who dyno'd over 200rwhp with stock cam and heads?

    Hey guys just wondering for those who have dyno'd over 200 rwhp with a stock and heads, it seems that everyone of them had a larger maf, and intake, do you also have a custom or mail order chip, or tweecer type set up? Just curious as to how big of a restriction the stock maf is? A :shrug:
  19. twotonefreak

    86-93 LT's on 95 GT **Need specifics**

    I have Hedman 86-93 LTs on my car and they fit great, they are also a one piece flange. Only downside is I have to pull the RH header to remove the starter but that isn't a big deal at all.
  20. twotonefreak

    best exhaust set-up!!!

    I have Hedman LTs, o/r X pipe, Spintech Pro Streets, 2-1/2" Tails and it is badass, no drone in the cabin and just a very authorative, very loud note out the tailpipes!
Top Bottom
Back
Forums
Menu