Search results

  1. MT1083

    Anyone here with a Dell Axim X3 PDA?

    If there is anyone here with the mentioned PDA, I was wondering if I could at all trouble you for some help. I had this PDA for a few years up until about a month ago and I think it was stolen. I still have a current backup on my computer of what info was on it. My father has an Axim X5 that he...
  2. MT1083

    Cobra T45 crossmember...

    get a hold of randy stinchcomb on here or modular depot.
  3. MT1083

    Noise issue with BFGoodrich g-Force T/A KDW-2 (NT)??

    Mine weren't very noisy until after 5k miles. Now I can hear them, but my car is loud anyway so I don't really notice it that much.
  4. MT1083

    Changing tranny oil

    Another incredibly easy way to fill the tranny is to remove your shifter and pour the fluid in the top of the tranny until it starts to come out of the fill hole. I used about 4qts in my t-56.
  5. MT1083

    Quick T-45 Q...

    Thanks Mike! I was hoping you would chip in. So basically, outside of a few connectors being different the swap should work?
  6. MT1083

    Quick T-45 Q...

    I did a few searches but for some reason I'm drawing a blank. I need to know if a T-45 from a 00GT will swap into a 98GT. I think I found that the 98 uses a mechanical speedo...so that may be a problem. Is that the only thing or are the tail housings different too?
  7. MT1083

    MGW Shifter Install

    Just use the stock lower dust boot with the rubber grommet that mgw supplies.
  8. MT1083

    MGW Shift stops

    Yeah I was under the impression that the t-56 and t-3650 had the built in stops but not the t-45.
  9. MT1083

    T45 to T56 conversion in 2000 GT

    you'll need a shorter driveshaft or a cobra droveshaft, modified crossmember or just buy a cobra crossmember, wire up the reverse lockout solenoid, bang out the tunnel a little where the tranny rubs. If you go with a cobra driveshaft, you will need a cobra pinion flange.
  10. MT1083

    Going to put in fuel pressure gauge with my KB... need a little help.

    Are you sure that you have a schrader valve? I can't remember what year they started removing them. If you don't have one then you need to buy another type adapter from KB (I can't remember what its called). My fuel rail had the valve in it though and I used a 90* fitting so that the sender is...
  11. MT1083

    Exhaust Install

    as for the xpipe you can do it with no problems 1. Jack the car up as high as you safely can. 2. be sure to have decent selection of extensions and a swivel or two. 3. might need to soak the nuts in pb blaster or wd40.
  12. MT1083

    Bassani X-pipe With...

    I've tried the following: stock h w/ bassani c/b Catted X w/ catback o/r X w/ catback The stock h is still quiet with the catback and kind of disappointing after having the x in there. The catted x and catback has a nice rumble to me and is not too loud to wake up the neighbors just...
  13. MT1083

    Bassani X-pipe With...

    I'll try to attach it...lemme see if this works. Actually now that I try it, I don't think you can attach wmv's.
  14. MT1083

    Bassani X-pipe With...

    I have a soundclip of a bassani catted x w/ the bassani catback. If you want it just pm me and I'll email it to ya.
  15. MT1083

    problem with upr control arms

    yeah I called them and they immediately shipped them to me.
  16. MT1083

    The Acronym Decryption Thread

    O/R = offroad midpipe
  17. MT1083

    Transmission Removal?

    yep extensions and a swivel socket.
  18. MT1083

    Question for Convertible Owners with Bilsteins or anyone else who can Help

    I use the Bilstein HD with H&R race springs and love them. The ride is firmer but not harsh. I've had other guys ride in my car who had other combos and immediately want to swap to bilstein's.
  19. MT1083

    KB 1.7

    yes you can use the 75mm TB. 3.90's will be ok but I hope you have stock in a tire company. :D
  20. MT1083

    steeda says yes maximum motorsports said no...

    I would listen to MM over steeda any day.