Search results

  1. N

    Vortech S-Trim or Powerdyne Supercharger

    So if i'm a guy that does a little "light to light" action every now and then and will never put my car on a track, the Powerdyne might be a good choice?
  2. N

    Dome light/Electrical Question...

    Already did a search - Simple electrical problem... I've been visiting here for years and have been able to find answers and opinions to practically every question via searches, but couldn't find this one... Car: 1990 GT Problem: Dome light wont turn off and drains the battery...
  3. N

    Thought I was done...Need combo help...

    After researching and getting opinions from many of you here i decided on a combo that includes just about everything on the top side of the motor. Now I've since decided to rebuild the motor with CHP's 347 Stroker kit. It'll be a daily driver ('90GT) - but I only do about 15 miles a day tops...
  4. N

    Please Rate This Performance Kit

    Are the AFR 205's street and emissions legal though?
  5. N

    Please Rate This Performance Kit

    I've decided to go a slightly different route. Since I'm basically rebuilding the top of the motor, I'm going to rebuild the bottom as well and throw in a CHP 347 stroker. Will these same mods be optimum with the stroked motor?: Edelbrock Aluminum cylinder heads Crane 2040 Cam Edelbrock...
  6. N

    Please Rate This Performance Kit

    Thanks again for your responses...My next question is with this particular setup, would 24lb injectors be necessary or beneficial or both?
  7. N

    Please Rate This Performance Kit

  8. N

    Please Rate This Performance Kit

    I’m learning as I go and you guys have been like a Mustang encyclopedia for me. Thank you, truly. Now I need some help evaluating this combo available at Brothers Performance in Corona, CA for about $2500. This is the combo: Edelbrock Aluminum cylinder heads Crane 2040 Cam Edelbrock...
  9. N

    Rate this suspension kit for me...

    I'm getting the package from Brothers Performance Warehouse in Corona, CA. They're pretty quick with the shipping if you order by phone or internet. (www.brothersperformance.com) They do offer similar kits with the Koni shocks and struts, and all are available with specific or progressive...
  10. N

    Rate this suspension kit for me...

    KYB Gas Struts and Shocks BBK specific rate*1.5 lowering springs BBK polyurethane front bushings package(includes sway bar,strut mount end link bushings,and BBK2508 offset rack bushings) Cost: $425.99 Please rate the quality/cost for me. These parts would all be replacing original parts...
  11. N

    Pro50 - How to re-use Inner Boot?

    I finally figured out that the instructions suggest you cut out the center of the outer boot (the one that covers the hole in the floor pan). Once done, it fits snugly around the circular part of the base of the shifter, cutting down noise and protecting the shifter from debris.
  12. N

    Pro50 - How to re-use Inner Boot?

    There are two rubber boots TOTAL...There's the one that fits over the circular part of the shifter base, the other attaches to the metal plate and covers the hole in the floor pan...I'm speaking of the one that was originally around the round part of the stock shifter base and secured with a...
  13. N

    Pro50 - How to re-use Inner Boot?

    Yes, siliconed the base...The base of the Pro50 is wider than the stock shifter though...In this case I wouldn't reuse the snap wring? Also, the gear stops cause a problem on the inside and outside... Am I overthinking this?
  14. N

    Pro50 - How to re-use Inner Boot?

    the directions say to trim off the bottom.does it fit over the new shifter or does it go inside?
  15. N

    Pro50 - How to re-use Inner Boot?

    I'm installing my new shifter (with the Kona handle) and have gotten past setting the gear stops, I've test driven and am putting it back together now... The Pro50 directions talk about reusing the inner boot but I'm not understanding how to... Can anyone help explain this to me?
  16. N

    Got my Kona!

    Anybody else gotten the Pro5.0 with the Kona handle? After much debate, ordered mine to replace my stock shifter back on 4/15 and it's not due to arrive until 5/3, just within the 7-12 business days they said it would take... I'm hoping to get a little more input from those who've purchased...
  17. N

    Quick question about window molding removal

    Yes, I inted to flat black paint them and put them back on, which is why I'm trying to limit damage during removal. Right now they're faded and it really takes away from the appearance of the car. I know I could buy them new, but am trying to save money for performance parts.
  18. N

    Quick question about window molding removal

    What's the safest way to remove the front and rear window molding on a 90GT without damaging the molding, and without that pronged tool specifically for this application? I want to take them off and spray them. Thanks in advance, folks.
View older results
Top Bottom
Back
Forums
Menu