Search results

  1. golf4283

    Front Blinkers Wiring Issue

    When the headlights go on both park lights should go off. there is something mis-wired on the passenger side.
  2. golf4283

    Going To Bore 0.030 Over My 250k 96 Explorer Block And Gt40 Valve Job. Need Cam Advise Please!

    I have my 302 bored .040 over and am running ported GT40's with a 3 angle valve job. I'm running a comp XE-276 and it sounds and runs really strong.
  3. golf4283

    Stangnet Forums Hacked? - Solved

    Just ran an ad-aware scan and it got rid of some tracking cookie. Seems to be working fine now so who knows. hopefully that was it.
  4. golf4283

    Stangnet Forums Hacked? - Solved

    haha I wish it were so. I just don't understand how it's only this website that does it.
  5. golf4283

    Stangnet Forums Hacked? - Solved

    Has anyone else been being redirected to buy Justin Beiber tickets when going to Stangnet? I can sometimes get through and then sometimes I'm redirected to buy tickets through ticketmaster Austrailia. This doesn't happen to me on any other website except stangnet so I don't think it's my...
  6. golf4283

    Rod And Main Bearing/journal Undersize

    Yea I agree. Just have it reground. The machine shop I used charged me $60 to check and polish mine. They took .010 off so I just got the over(under?)sized bearings. Installing the bearings for the Main and Rods is simple and requires no tools. Cheap insurance against future problems IMO.
  7. golf4283

    Ect Sensor Grounding

    I'll snap some pictures. Honestly though it's a pretty basic solution. And before I post a couple pictures I'll say that 1" was wishful thinking. It's probably about 2-3" down the line. I can get it closer though by modifying my setup. I just did it the way I did for ease of installation. I'll...
  8. golf4283

    Ect Sensor Grounding

    Yea it's definitely running rich right now. Just fired it up for the first time yesterday and set the timing/idle. The sensor is located approximately 1" further along the heater supply line than the stock location so that shouldn't be an issue IMO. the thing is it's currently not grounded so I...
  9. golf4283

    Ect Sensor Grounding

    Awesome! Thanks. That must be why I'm running rich/having hard warm start issues. I'll ground the guage. It appears Brass isn't as conductive so I'll make sure to ground the gauge itself rather than the T fitting. Thanks!
  10. golf4283

    Ect Sensor Grounding

    I have a quick question. Does the ECT sensor need to be grounded? The original installation is on the heater pipes which are metal and provide a ground via the ECT sensor itself. On my setup I'm running rubber hoses and using a brass "T" fitting and plugging the sensor into the T and passing...
  11. golf4283

    Digital Tuning Efi Conversion In San Diego

    When removing the EGR and smog did you make sure to fool the computer into thinking it's present? I believe the system goes into limp mode when EGR isn't present without a resistor being isntalled. After that start by unplugging the TFI module as well as the IAC valve. Start the engine set the...
  12. golf4283

    Which Efi System?

    I agree with Rusty. I went with the stock ford Mass Air setup with an A9L computer in my car. Parts are cheap and redily available over the counter or at the junkyards and you have yourself a geniune Ford product in your car. The aftermarket systems all look nice as well but just seem too...
  13. golf4283

    66 Coupe Back Seat

    ok check in the upper right of the page, it should show you a message, I'm PMing you right now.
  14. golf4283

    66 Coupe Back Seat

    I have a set of rear seats. PM me and we can discuss there.
  15. golf4283

    Gt40 Intake Question

    So i installed a GT40 intake and am going EFI in my '65 and I have a question regarding sensor placement. the GT40 lower intake I have has 2 rear threaded ports on either side. My question is are the readings at those ports as accurate as ones where the coolant is flowing? the intake doesn't...
  16. golf4283

    T5 Reverse Light Connector

    if you don't want to buy the pigtail just go buy some crimp connectors and you can McGyver rig it with the crimps. It's gonna be ghetto though. Why not just spend the money to do it right. I've learned over the years it ends up being cheaper to do it right once than wrong the first time.
  17. golf4283

    T5 Reverse Light Connector

    on the T5 I believe the reverse light connector is on the drivers side of the trans. it's a 2 prong looking guy and you can buy a pigtail for it here (http://www.rjminjectiontech.com/collections/pigtails-connectors/products/backup-con). Your best bet is to go under the dash and cut the reverse...
  18. golf4283

    Battery Wiring Question

    I like that setup too. I wasn't sure on Fuse size so I'll just use the same size you are. I want to run it through the cabin though so I can tap the source for my various harnesses I listed.
  19. golf4283

    Cobra GT40 Heads & Cam options

    Chris where in Indiana are you? I'm in the market for a short block and live in the south suburbs of Chicago.
  20. golf4283

    Courtesy Lights Won't Turn Off

    check the door switches. it's possible they're broken.
Top Bottom
Back
Forums
Menu