Search results

  1. FastA$$89Vert

    Possible to pass Emissions w/o smog pump?

    I dont have one and I passed.......they dont look for it visually even though they are supposed to (NJ)
  2. FastA$$89Vert

    Best way to seal differential cover?

    Nope, No open end on the rear, you put the bolt right into the rear and its closed along the back of it. I could have tried to make a bigger thread in there, but I would have also had to make a bigger hole and re thread the diff. cover also....so for now Im gonna see how it works when I get the...
  3. FastA$$89Vert

    Best way to seal differential cover?

    Yes I cannot put the bottom bolt in because the rear itself is now stripped and i Was unable to thread it..... I sealed it up best I could, i have a feeling it will leak
  4. FastA$$89Vert

    Best way to seal differential cover?

    Well I tried to get that bolt out and it didnt work, now i have a hole there (crooked) with no threads......i basically jus drilled it out, i had no chance at it. Now its never gonna seal right without that bottom bolt :nonono:
  5. FastA$$89Vert

    Best way to seal differential cover?

    Directions said make sure they dont touch at all....... Of course I run into another problem, one of the original bolt heads broke off, now i have to find a way to get the bolt out of the rear completely flush with where the cover would be........ any ideas
  6. FastA$$89Vert

    Best way to seal differential cover?

    I got one of those summit rear kits with the cover bolts etc. They give you these long bolts with a flat pedastal on the end, does the pedastal go into the rear against those caps?
  7. FastA$$89Vert

    Best way to seal differential cover?

    Im assuming you would use sealant with you put a new cover on....will hylomar do the job?
  8. FastA$$89Vert

    AC Problem.....

    Ok I just got a different recharge kit and when that thing is not spinning, the pressure will build up to 60(red on gauge) then it will start spinning until it drops down to 25 (green) and this is continuous. The air is semi cool, but nothing like it should be.
  9. FastA$$89Vert

    AC Problem.....

    I had it on Max A/C and it was still doing that off and on.....the air is not getting cold either....Im about to charge the system, but I want to be sure the compressor isnt shot first.
  10. FastA$$89Vert

    AC Problem.....

    When I turn the AC on in a 95GT, should the front of the compressor spin? When I turn it on, it will spin for 2 seconds and then it will stop, and start spinning again a few seconds later...on and off. The pulley is always spinning but the front parto f the compressor is whats turning on...
  11. FastA$$89Vert

    89 gt vs ls1

    Yikes. Your gonna need a built motor to hang with him. No way around it. 347 stroker with a big blower could do the job.
  12. FastA$$89Vert

    post the best way to build to get LOW END TORQUE!

    If your looking for low end, B cam is not the way to go. That makes more power above 4000. The e-cam makes great power down low.
  13. FastA$$89Vert

    No air coming from vents??

    I have the same problem, so.....TTT
  14. FastA$$89Vert

    one last time, will this fit?!

    Im going to pick up the F-303 cam wednesday and I wanna make sure it fits with my Edelbrock 6025 heads with 2.02 intake valves and 1.6 rockers. am i good to go :banana:
  15. FastA$$89Vert

    Best cam bang for the buck?

    No one said the X cam..............maybe too much for my setup? With that much lift would it even fit without modification to the pistons....the heads I have are 2.02 intake valve.... The TFS Stage 2 requires 9:5:1 compression. Im not sure but I think I only have 9:0:1
  16. FastA$$89Vert

    Best cam bang for the buck?

    Im looking for a more aggresive cam than the E-cam, I dont mind some rough idle, heads and intake are getting ported now and i wanna make some more power, but nothing to extreme, whats the best bang for the buck since everyone is saying alphabet cams are outdated?>
  17. FastA$$89Vert

    What shop would do this?

    oK heres the story, my car is torn down to just the block, pistons, rods, lifters etc in the car. I want to switch cams, but the cam is the part we dont really wanna mess with so id rather have a shop do it. Anyone know a shop that would swap cams if i brought the car to them? somewhere in...
  18. FastA$$89Vert

    Can you install cam.....

    without removing the motor from the car, or taking the front bumper off
  19. FastA$$89Vert

    Power Loss through Drive Train?

    I used to have the crate motor you are talking about. I can tell you this. They get those numbers assuming you have electric fan, GT-40 Upper and Lower and some other stuff. I had that setup with the cobra upper and lower and even had 1.7rr and it dynod at 271rwhp/304rwtq but it was never...
  20. FastA$$89Vert

    Need Advise On 5.0 Quick!!!!

    Maybe Im not much of a collector but no way would I pay that much for a 5.0 with 125k miles. Buy a nice condition fox body cheap with a lotta miles and throw a new motor in it, thats how I would spend my 7k
Top Bottom
Back
Forums
Menu