Search results

  1. maypo59

    Installing MAC Air Filter - Am I Retarded?

    I fought it for a few minutes, then made room for my arm by removing the front wheel and then unclipping/screwing the fender liner and pulling it down and back. Would have been a 10 minute job had I just done that at first...
  2. maypo59

    will a worn rag joint make the car "wander"?

    could be toe.. put a straight edge outside of both tires and measure in front and behind the tire, should be just a little less in the front.(1/32) or so
  3. maypo59

    Where can I buy fender flares?

    BTW, when you call the dealership, ask them to look up "export flairs" that is the actuall name for them.
  4. maypo59

    BBK SSI Series Intake

    Magazines have tested it, they seem to like it, near as I can tell, you would need to use an elbow, elswise, should work.
  5. maypo59

    Can't get rotors off...help!

    not a "trick" but the rear pistons TURN in, not press in.
  6. maypo59

    Can't get rotors off...help!

    hit it harder.
  7. maypo59

    Anyone Use the Summit Racing o/r h pipe?

    I have one, no problems.
  8. maypo59

    rear upper control arm bushing question

    I used a sawz all... worked pretty good. I cut each at three places, then pried it out. I used poly from 5.0Resto.
  9. maypo59

    Installing aftermarket hood/ hood pins

    If you remove the latch itself, you will find it is located by 2 pins/studs. If you remove those, you can adjust the latch mechanism to wherever it needs to be to lock. I had to move mine down about a 1/4" to get it to lock perfect. You need to find out why the bolts are not getting snug.. you...
  10. maypo59

    Installing aftermarket hood/ hood pins

    I don't know of any studs that hold the hood on, do you mean the bolts that go into the hinge bracket? If so, and they are bottoming out, you need shorter bolts. If the hood is to high/low in the back, then you need to raise/lower the hinge. If it won't line up along both fenders, you need to...
  11. maypo59

    c-clip elimators + disk brakes. Why not?

    The eliminator goes on the end of the axle housing, I have always understood that it interfered eith the caliper, or the sensor ring.
  12. maypo59

    Dealings with ABC Exclusive parts, anyone?

    subscribing.. I want their cobra with lip front bumper cover... waiting to here reviews..
  13. maypo59

    Wheel spacers

    Damn, I have the elcheapo ones.. But, I have not had a single problem with them.. Been fast, been autocrossing, no problems.
  14. maypo59

    off set steering rack bushings

    Yep, holes closer to ground, you want to move the rack up... since your lowering springs effectivly moved your tie rod ends up..
  15. maypo59

    Info on Cobra brake install

    I havn't had any cracks or problems with my cross drilled and slotted rotors, and they have been to several autocrosses, and general driving around, I have the cobra upgrade in the front and the Baer eradispeed in the rear, BUT, I will say this, when you get on the brakes, they "buzz" as the...
  16. maypo59

    Problems resetting keyless entry

    as I remember I ended up using a pair of needle nose pliers I think... here is alink to EXACTLY how I did it on mine when I discovered I had keyless entry, then went on eBay and bought a couple fobs.. http://www.ponyperformance.com/index.html
  17. maypo59

    BAD DISTRIBUTER???????? pLaEsE hElP

    A rebuilt one can be had at AutoZone for $89.
  18. maypo59

    Passenger One Push Down Window

    I haven't done it, but my guess is it works like the drivers side, plug and play... pull of the door panels and compare?? The connectors should be able to figure out.
  19. maypo59

    How long does it take to install a supercharger kit?

    If you are very mechanically inclined, and have all the tools/parts, you should be able to do it in less than a weekend.. if not.. well... longer. did you: install your own gears? your own HCI? Can you adjust your own timing?? Have you changed your own clutch?? Have you done your brakes?? Have...
  20. maypo59

    e-brake question

    I don't think you can put too many turns on it. The instructions to rewind it are in the haynes manual, but it's not hard, just takes three hands.you wind it up untill you can pass an allen key or something through the hole in the housing to hold it in place, then mount it, run the cable, pull...
Top Bottom
Back
Forums
Menu