Search results
-
Progress Thread Almost ready for the road, Need input for parts!
The heads are AFR 185's like I said the motor is completely done just getting ready to finish putting in the AOD-E and program the comp-u-shift. The just have to run the -8 fuel line from the fuel cell to engine bay and drop it in.... They Dyno pulls turned out as expected 446hp 436ft lbs- jpope417
- Post #6
- Forum: Fox 5.0 Mustang Tech
-
Post pics of how your foxbody currently sits
Cars in a different state..... But I have the motor!!!!! Seriously just meed to go pic up the car and throw this in- jpope417
- Post #1,135
- Forum: 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
-
Progress Thread Almost ready for the road, Need input for parts!
I was thinking that 2 but I got the axels for free so I was thinking go with the SVO calipers in the front and switch the rear over later, then even further down the road (when I use the C4 and trans brake with slicks) and snap and axel I figured I would buy the front end conversion and the rear...- jpope417
- Post #3
- Forum: Fox 5.0 Mustang Tech
-
Cooling Question
Did your check to see if your thermostat is sticking???? Mine had the same issue way back in the day, It would almost over heat all i would have to do is give a good solid tap the housing with a hard object (dont use metal) U used a rubber mallet and it would open on its own till the car sat...- jpope417
- Post #22
- Forum: Fox 5.0 Mustang Tech
-
Progress Thread Almost ready for the road, Need input for parts!
Hey Guys, I have been on here for a little while but I have not been active at all because Ive been so busy. My names Jake and I will probably be on this site a lot now that I'm back to daily wrenching on my 5.0. I am a little more skilled then you avg garage monkey but I am not a master...- jpope417
- Thread
- Replies: 30
- Forum: Fox 5.0 Mustang Tech
-
Imported Item
On its way to the Dyno for tuning and #'s- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
New pulleys and other accessories to come, Some old stuff on here just to get it in the car.- jpope417
- Media item
- Comments: 3
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
CP Pistons with Scat Rods- jpope417
- Media item
- Comments: 3
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 1
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
Looking Good!!!!- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
I called Comp Cams and they said a custom grind would be best for my set up so this is the specs- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
YES I KNOW IM SHORT ONE FREEZE PLUG LOL- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
SCAT CRANK- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
PROPER TOOLS FOR THE RIGHT JOB- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
HAD TO HAND FILE EACH RING- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!
-
Imported Item
- jpope417
- Media item
- Comments: 0
- Album: Start of my 5.0 project.... Motor build pics!!