Search results

  1. BDAWK2002

    How Much $$ For My Cobra's

    I just bought a set for $400 with good tires.Wheels where a little beat up though....
  2. BDAWK2002

    new clutch....breaking it in

    I got the FRRP king cobra clutch...I put it in when I did the 5 spd swap.I'm just finishing up the 500 mile break in and still have a little chatter but nothing like when it was first installed.I still have some heavy chatter in reverse though.My throwout bearing is squeking like a b**ch also...
  3. BDAWK2002

    Owners Manual

    www.helminc.com
  4. BDAWK2002

    Crossmember

    It's barley noticeable...When you have it the wrong way the bolts almost go in but they dont.Like I said I was under the car for a little while trying to figure this one out .I have a aftermarket urethane trans mount so I had to screw in bolts it didnt have studs like the stocker.If it doesnt...
  5. BDAWK2002

    Crossmember

    The ones for auto's and 5 spd's are the same.
  6. BDAWK2002

    Part Number

    If the Ford guy is searching for the pulley for a mustang he wont find it.The pulley is not offered unless you buy the whole p/s bracket which is like $400.If your lucky maybe it fits a different car and someone will hook you up with the part#.I just went through the same s**t and ended up...
  7. BDAWK2002

    R is for rice?

    They should put a tow hitch on so it can tow a big flashing sign that say 5.8...lol
  8. BDAWK2002

    Failed emissons in N.J.......help........

    Thanks for all the replies guy's.........I'm pretty convinced it has to be the EGR valve.I'm gonna take it off tomorrow and check to see if it's working.My cat's,sparkplug's,cap&rotor& my o2's are all brand new so it shouldnt be any of them.I usually run 89 octane gas I put the 94 in because I...
  9. BDAWK2002

    c/c plates.....where to get em?

    I got the STEEDA ones... :nice:
  10. BDAWK2002

    Failed emissons in N.J.......help........

    My timing is not advanced still at the stock setting but I havent checked it in a couple of years.I have never ran injector cleaner through my stock injectors but I will tomorrow.The air cleaner is clean,i'm running a cold air setup so the filter is in the fender.The reason I have a 5spd...
  11. BDAWK2002

    Failed emissons in N.J.......help........

    I just failed inspection because of high emissons.The guy told me it failed because of a high NOX reading.It is supposed to read 907 and mine read 1259.The guy told me NOX has somthing to do with the temp of the gas in my exhaust and he want $120 just to try and diagnose what the problem...
  12. BDAWK2002

    Oxygen Sensor Part Numbers

    The BOSCH o2's that I got are part# 13127.I have a Bassani exhaust and they fit no problem without any wire exstensions.When mine went bad I got codes 171 &172 which is for a bad rh side sensor.I changed both of them just to be on the safe side.They cost me like $65 each at pep boys.......Good...
  13. BDAWK2002

    Crossmember

    Yes it is offset!!!If it doesnt fit right spin it around and it should line up.....Took me a little while under the car to figure that out. :D
  14. BDAWK2002

    Oxygen Sensor Part Numbers

    I just bought 2 Bosch o2's a few day's ago.When I bought them there was two listings,one for before cat and one for after cat.I got the one's for before cat and they worked fine and plugged right into the factory plugs.They where like $65 each.I will see if I can get the part#'s for you...
  15. BDAWK2002

    Alignment question

    I have Steeda sport springs and Steeda c/c plate's(the 3 bolt ones).I'm going to bring my car in for an alignment tomorrow and was wondering if I should tell the place any special instructions.The car is lowered like an 1 1/2.Does it still get aligned like a stock mustang or does it need special...
  16. BDAWK2002

    Woooooooo-Hoooooo...no more aode

    Took off the dogbone last nite.Vibration is a little better but not gone I think I can live with it.My check engine light also came on while driving home from work last nite.I pulled the codes and got 171 & 172 rh side o2 sensor.So I put in a new pair of O2's and now no more lite.Chatter is also...
  17. BDAWK2002

    Woooooooo-Hoooooo...no more aode

    My first stangnet pics!!!!!!!!Clear cornerlites soon to be installed
  18. BDAWK2002

    Going to change motor mounts, any advice???

    Did you have to unhook the exhaust to jack the motor up or is there enough play to get em out?
  19. BDAWK2002

    Woooooooo-Hoooooo...no more aode

    I put in a new TKO500 so I filled it up before the first drive.The place I bought it from sent me 4 quarts of fluid but it only took 3.I havent checked it since I drove it so I'll check it again tonite when I get home to make sure it doesnt need more.
  20. BDAWK2002

    Woooooooo-Hoooooo...no more aode

    I put a little lube on the inside of the bearing where the input shaft slides through but not a lot I was worried about grease getting on the clutch.When i heard the sound the first thing I thought of was the t/o bearing.So you think the vibration is norm???It's not to bad I'm hopeing taking off...
Top Bottom
Back
Forums
Menu