Search results

  1. BlueMonster65

    Cam/timing gear dowel question

    auto parts store only two different length dowels were used on 302's so any auto store should have what you need. usually both come with the cam install kit. just as a side note, i think the 74 302 had the retarded timing chain set so if you havent already now would be a good time to change...
  2. BlueMonster65

    Carb jetting for A/F ratio

    start at the beginning, check float level, fuel pressure then after you set the idle transfer slot opening to .020" per demon specs. and adjust the idle mixture screws to obtain the best vacume reading, make sure your idle is where you need it to be say 900rpm by using the idle eaze circuit...
  3. BlueMonster65

    how much hp with this exhaust set up 5 hp at least?

    not exactly its not that simple well maybe it is. the key is to not go with too big a pipe right after the collector for about the first few feet. general guidlines suggest 2 1/4 pipe for under 300hp 2 1/2 for under 400hp. what i am suggesting is that by mixing the pipe sizes a better exhaust...
  4. BlueMonster65

    Holley Avenger OR Road Demon

    i ran a road demon 625 for quite some time, never had a problem, and was a significant improvement over my holley 4010. i switched to a holley 600dp 4150 that i modified for blowthru supecharging. if BG made a demon for blowthru i probably would have bought that vs. modding my old holley...
  5. BlueMonster65

    how much hp with this exhaust set up 5 hp at least?

    exhaust science from what i have read the ideal setup for an exhaust on a street car with 300hp to 400hp would have long tube headers with 1 5/8" primarys and 2 1/2" collectors then 2 1/4 pipe then to a 2 1/4 or 2 1/2 h or x pipe. 2 1/2 pipes out of the crossover pipe to a 2 1/2" muffler...
  6. BlueMonster65

    installation of ATI p600b sc complete

    i suggest removing the pusher fan and see if that helps. generally fans should not be used in tandem like you have it. the pusher will be a restriction to the puller since it is the more effiecient way to cool. your effective cfm is probably less than 2200cfm, not the 4400cfm you might think...
  7. BlueMonster65

    installation of ATI p600b sc complete

    is it a becool fan? are you saying you have more than one 16" fan. if so their air paths must not cross, otherwise they will be fighting eachother. check to make sure the fan is working if it is and is a becool, do what i did and throw it in the garbage or give it to a homeless shelter...
  8. BlueMonster65

    installation of ATI p600b sc complete

    i still dont think that pump will be good. fuel pressure is not the only requirement for a blow thru application. the pump needs to be able to provide the volume of fuel required to make the horsepower level desired at the pressure level required by the boost you are trying to run. for...
  9. BlueMonster65

    installation of ATI p600b sc complete

    i'm running a mallory comp110FI pump with 4307m regulator. its an electric efi pump. i run a base pressure of 7psi and the reg. rises pressure 1 to 1 with boost. i spent probably a thousand on the fuel system between the fuel cell, pump, lines, fittings, and filters. it is NOT a good idea to...
  10. BlueMonster65

    installation of ATI p600b sc complete

    no actually the car runs cooler now since i installed a becool aluminum radiator out of a 69 camaro and a permacool fingerchopper electric fan. i was having a problem initially with the becool fan but after i switched it, it stays right a 160deg. there were many obstabcles with this project...
  11. BlueMonster65

    installation of ATI p600b sc complete

    so far its a stock bottom end with cast 9.7:1 pistons. it pulleyed for 9psi. its made 6psi at about 5grand with no problems. but i'm still working out the bugs. it should be good for aboiut 450hp flywheel so as long as it doesn't go lean the cast pistons should be ok. especially since its...
  12. BlueMonster65

    supercharge on carb

    just finished adding a ATI procharger to my 65 with a carb. its totally insane. i took a used 5.0L mustang kit for a third of what it costs new and i modified most of the brackets and accessories to make it work. turbomustangs is the place to go. just about everything on blowthru carb...
  13. BlueMonster65

    installation of ATI p600b sc complete

    well its been awhile since i posted here. i've been busy adding a p600b procharger to my 65 mustang. iprior to the supercharger the car made 220hp and 260lbft torque at the rear wheels ona dynojet dyno. i still have some serious tuning to do before i can get some dyno numbers but on my...
  14. BlueMonster65

    good old exploding tank question..

    gas tanks believe it or not that is one of the safest places for the tank to be located. most if not all new cars have the tank located under the rear seat of a passenger car. this is because it is least likely to be impacted during any accident. anyway i switched to a fuel cell mostly...
  15. BlueMonster65

    speaker box dimensions

    i made side panels to mount my crossover and capacitor on and i used plywood for the panel. i took some cardboard and cut it to make the desired shape of the panel then transfered that to the plywood. to mount the panel to the floor i used a piece of angle iron. and screwed it to the panel...
  16. BlueMonster65

    speaker box dimensions

    yep yeah i have plans on my website http://bluemonster.freeservers.com i havent updated it in a while but they should still be there. its for 2 8"'s. i suppose you could fit two tens by making the depth a little more to increase internal volume. the plans are for about as simple a box you...
  17. BlueMonster65

    HOW LONG MUST WE WAIT ?? FROM ORDER TO ARRIVAL ?? ANYONE WAITING LONGER THAN THIS ??

    i ordered on 11/13 and nothing yet. i don't even have a DORA. the botard at the dealership who i originally worked with is no longer there. i question whether they even put my order in at all. if he failed too, i wish bad things on him.
  18. BlueMonster65

    colors for next year?

    i wonder what Vista Blue looks like? is it on any existing cars but called something else? and for the love of god why won't ford put a dark green on this car! it's begging for it.
  19. BlueMonster65

    300HP? Thats It...Whats wrong with Ford

    "Sucks that the 50's tech works better " no it doesn't. What are you talking about? lets go back to points + condensors and bias ply tires while were at it. the 4.6L is a small engine 281cuin. GM's engine only makes more power because it is larger. and not that i am defending the LS1 but it...
  20. BlueMonster65

    price of dealer option bullit wheels?

    according to my brochure those bullit options are 17" wheels and the dealer gets $325 for each wheel. better to get some aftermarket 18" wheels from discount tire direct or tire rack.
Top Bottom
Back
Forums
Menu