Search results

  1. 50gt1988

    Need a balancer for..

    Pioneer is a really good piece too.
  2. 50gt1988

    Long Tubes

    Wow those are odd. Ok first dont get those they look custom built for something.......they aim at the ground which is wierd. Also bbks are marked with like a metal badge on the driverside header and Macs look nothing like that.
  3. 50gt1988

    What do the cop cars run in a 1/4?

    Up here in Washington some cities are switching to the Dodge Chargers with the new Hemi's. I've seen one sofar and it's wierd.
  4. 50gt1988

    Mechanical oil pressure question

    yeah a T would help to not have a dead gauge but it doesn't have to be there.
  5. 50gt1988

    Long Tubes

    I run bbks on my road track car and am very happy with them. I also had a set of really nice Macs when I was building the motor but they didn't fit with the t-sump oil pan I am using. So if your running a normal pan either mac or bbk are good. The BBKs were really easy to install and are...
  6. 50gt1988

    Power Loss with Injector swap??

    Yeah I actually just worked the numbers myself and decided on the 30s. Oh and I plan on getting the Anderson Motorsports unit anyway so it's not a quick decision. Well does anyone know how to go about sending in a Pro-M meter to be re-calibrated?
  7. 50gt1988

    Power Loss with Injector swap??

    Alright well I've read all the responses and it sounds like I made a bad injector choice. I'm going with an Anderson Motorsports Tuner so could I set the injectors to a lower pulse?
  8. 50gt1988

    Power Loss with Injector swap??

    Ok I just installed a new set of 30lb injectors and a pro-m 80mm mass air meter into my car. Now and then when I shift to second or third there is a second of power loss then it kicks back in as if nothing happened. Any ideas??
  9. 50gt1988

    which flywheel?

    I just used a billet steel with my centerforce only because centerforce suggests a billet steel for their clutches.
  10. 50gt1988

    New DSS 306 w/AFR185... pinging bad.. questions..

    I just got running in my car basically the same setup and my timing is set at 14 with no ping. Runs great.
  11. 50gt1988

    Flywheel Vibration

    Yeah the engine should be balanced for a 28oz and I'm almost 99.9% sure that's what the Ram flywheel was.
  12. 50gt1988

    Flywheel Vibration

    I just installed my new motor and transmission and it's running great except for a horrible vibration coming from the drivetrain. It vibrates at an idle then gets worse and worse as rpms increase. I took the car to a shop to get dyno tuned and the technician told me the flywheel might be the...
  13. 50gt1988

    MAP + MAF???

    You've have helped me with codes before and the codes i pulled were all bad sensor codes that you said may be caused by a bad ground in the computer. Which is another reason I think its the ecu.
  14. 50gt1988

    MAP + MAF???

    Ok how would the car normally run if the Maf and the Map were connected? I did my maf conversion about 2 months ago and forgot to unplug the MAP sensor from the vacuum line and its run fine. I unplugged it and now it runs the same as it did before? Think my computers bad? BTW: My computers...
  15. 50gt1988

    Fuel system overkill????

    go with a 255lph while your at it, extra fuel will just be sent back to the tank by the FPR
  16. 50gt1988

    Help! Need a quick answer

    re-adjust clutch, if that doesn't work replace clutch
  17. 50gt1988

    control arm nut being a pain

    i hung my full body weight off a wrench under my car before mine broke loose
  18. 50gt1988

    Please help with main harness wiring issue!!

    Alright I did this conversion in my 88 GT and it works great but it will take me a long time to write up the post to explain how to wire the plugs so the best advise i can give you is to call the help number on the bottom of the instructions and ask the guys there, they will give you every step...
  19. 50gt1988

    Rear Stainless Steel Brake Lines

    Ok, I'm going to clear up some confusion. So you need the hard lines that run on the axle housing? Ok the easiest way to get those is to just take the car to a brake shop and they can make a set for you for about 20$. Stainless Steel lines are the stronger flexible lines that run between the...
  20. 50gt1988

    Finally Done...But problems!!! Experience Needed!

    Well during the break in I had it timed at 20 when it first started then when it was done i had it down to 14. I don't think the distrubuter is off a tooth, when the motor is at top dead center the 1# spark plug wire points straight at the intake.
Top Bottom
Back
Forums
Menu