Search results

  1. armand67Fstback

    Weighed my 68 Coupe.

    Car weight Good to know, thanks for sharing. I am going with a similar set up in a fastback. I glad to see it weighs under 3K. New Mustangs weigh a lot more than that.
  2. armand67Fstback

    1994 351W Roller Engine Question

    PoppyMod, yes that Is what I am trying to figure out. Will either be more powerful or more efficient?
  3. armand67Fstback

    1994 351W Roller Engine Question

    Can anyone explain the benefit of the scenarios below if I am going naturally aspirated on a 408W? 1. Flat top piston and a large combustion chamber head. (72cc combustion chambers) 2. Dished piston and small combustion chamber head. (58cc combustion chambers) I am aiming for low 10s...
  4. armand67Fstback

    1994 351W Roller Engine Question

    D.Hearne, thanks for the explanation, in reading it I realized the lifter retainer has an F7 code not E7.
  5. armand67Fstback

    1994 351W Roller Engine Question

    Thanks everyone your input has been very helpful. So I took most of the motor apart and saw a small amount of sand on the rods and on the pistons. I am thinking the engine originated from a farm truck. I also found out that the engine is from 1997, because the lifter retainers had a...
  6. armand67Fstback

    1994 351W Roller Engine Question

    Pistons and Valve Clearance I currently have the 351W (F4TE) down to the short block. Does anyone know if the pistons on a 1994 F4TE engine are cast or forged? I was also wondering if the AFR 205's need some valve clearance, can the pistons be notched more without removing the pistons...
  7. armand67Fstback

    1994 351W Roller Engine Question

    Clearances Thanks for the information, I will make sure to have the clearance checked, if it does not work then I will just go ahead and rebuild the engine locally so that these heads work. If it does work, the increase in compression will be a good boost. :D
  8. armand67Fstback

    1994 351W Roller Engine Question

    351W CarFreakGt, it is funny to see that I am influencing others :D I know what you mean, I have a 1991 5.0 HO and the 302 that was in the car, but I decided to buy a roller 351W. That means buying another intake and most likely headers. I already have ceramic long tubes for the 302 and...
  9. armand67Fstback

    1994 351W Roller Engine Question

    D.hearne and frdnut thanks for all of the good information. The engine was torn down to the short block and everything looks good on the engine. I have about $2200 to get it on the road. The two options I am looking with this amount of $ is an Air Gap RPM with Fast EZ-EFI. The second is a...
  10. armand67Fstback

    1994 351W Roller Engine Question

    AFR 205's If the stock heads on this engine are 64cc what will the AFR 205 head with 58cc combustion chambers do to the compression and drivability?
  11. armand67Fstback

    1969 351 w block ?

    Just curious, I opened mine up yesterday and saw the same thing. When I rebuild it is it worth making it any bigger to return more oil?
  12. armand67Fstback

    1994 351W Roller Engine Question

    My dad found two at a junkyard, so I have two to choose from. I am driving 3 hours to go see which of the two looks the best. If the stock heads are 64cc what will the AFR 205 head with 58cc combustion chambers do to the compression? Thanks for the replies so far, I am glad to see I am on...
  13. armand67Fstback

    1994 351W Roller Engine Question

    I needed some advice on a roller 351W. From what I could find these are supposed to have a compression ratio in the high 8's. From the factory they had the E7TE heads. What combustion chamber size do these heads have? If I get one of these stock engines with 80K miles can I install 58cc...
  14. armand67Fstback

    351W Build

    I have a question along the same lines in regards to a stock 1994 roller 351W. Can I use AFR 205 heads at the stock displacement and CR with a cam change? Later down the road I want to build a 408W and don't want to buy heads twice.
  15. armand67Fstback

    tranny

    Vote for 5-Speed I have a T5Z for my car. I can't wait to get it on the road! I like how a stick car burbles and pops when you let of the throttle in gear.
  16. armand67Fstback

    im restoring a 67 fastback

    67 Fastback Thanks for posting pictures, I like following build ups with pictures. I am also rebuilding a 67 Fastback. Armando
  17. armand67Fstback

    Best shock absorber for the dollar?

    Shocks I got QA1 single adjustable shocks from Summit Racing, with a 10% coupon code, price seemed reasonable for the quality. Sometimes CJ Pony Parts has specials and the price is fair for the set. My brother got his set there.
  18. armand67Fstback

    '65 347 2x4 winter project, SLOW progress

    Kevlar Clutch Velox, looks awesome. What brand/model of clutch did you go with? I have a Kevlar/Kevlar that I will be using that is made by a small clutch company.
  19. armand67Fstback

    Advice on buying new c4

    Performance Automatic C4 Palerider, you may want to check out PA transmissions. They are available at Summit Racing for about $1,100. You may be able to request a 1967 model C-4.
  20. armand67Fstback

    Got my Powerjection III running

    Powerjection III Iskwezm, any updates on this system? Is this the Powerjection III Plus with ignition control? Thanks
Top Bottom
Back
Forums
Menu