Search results

  1. HDTony

    It's Official, She Runs!!

    Ask and ye shall receive!
  2. HDTony

    It's Official, She Runs!!

    Quite the long project, of a 6 - 8 conversion. Custom 9" Built c-4 289 stroked to 347 - afr comp heads - Ed Curtis cam - Holley 670 avenger - Edelbrock air gap manifold - full msd ignition - all new steering and suspension - :poo:..... All new everything!!!!
  3. HDTony

    Sticky: I6 to V8 conversion

    we should go have a beer LOL
  4. HDTony

    What puller for tie rod ends?

    thats all I've ever used
  5. HDTony

    1966 I6 to V6 motor swap

    your looking at a lot of work. better yet, I have an inline 6 that runs great, with a 3 speed trans sitting here in my garage, just waiting for someone to come get it. I just pulled it out of my 65 $100 bucks and the whole setup is yours. give me a shout, 815 514 0380 -Tony p.s. I also have...
  6. HDTony

    Sticky: I6 to V8 conversion

    revisiting this thread.... as far as your cost analysis goes. If I told you the amount I have into this car I would be embarrased and I don't even have the motor in it yet, I could buy 3 v8 cars at this point. for those thinking about it.... my suggestion would be..... think long and hard before...
  7. HDTony

    Hard to find C4 351 bellhousing for sale $100

    C4 Bellhousing D3BP-7976-AA According to what I'm reading, it will fit these applications. 73-75 Pan Fill, 2-Bolt Starter, 164 Tooth flywheel, Small Block 351 Windsor D3BP-7976-AA 76-78 Pan Fill, 2-Bolt Starter, 164 Tooth flywheel, Small Block 351 Windsor, email me at [email protected]
  8. HDTony

    65 inline 6 and 3 speed for sale

    Its finally getting pulled out this week. Engine and trans run great and drive just fine. engine has ben rebuilt once by previous owner, so I cant honestly claim to know mileage, but she does not burn oil and runs smooth. Only reason Im pulling it out is I'm doing a V8 conversion. So the whole...
  9. HDTony

    Edelbrock 2121 intake manifold missing rear water ports?

    Glad I found this thread!! I was just fuming when I found my new edelbrock didn't have rear ports. LOL
  10. HDTony

    Cam gear question

    Thank you!! very informative post and you confirmed all my thoughts. it just so happened I also had a 2 piece with a tab in my stock pile of parts so I ended up using that. worked perfectly! thing is on and setup, water pump is on, now onto the manifold and carb. And don't worry wood snake...
  11. HDTony

    Cam gear question

    look at the pic I attached. particularly the center of the cam gear. the cam is recessed in the hole, I was thinking it should be flush or even with the front of the cam gear. good call on the dowel pin, looks like I'll have to make one custom
  12. HDTony

    Car spits/stumbles at low RPM under acceleration.

    Sounds like an accelerator pump issue to me.
  13. HDTony

    Cam gear question

    It's probably a simple question, but I want to make sure. Never dealt with timing gears before. With my cam gear the cam is not "flush" with the face of the gear? Is this an issue. People have told me its no problem, but I'm Leary about it. Also how important is it that the dowel rod protrudes...
  14. HDTony

    I want a C4

    Hmmm not sure why I never got a email alert for this, oh well. That sounds interesting, I'll check my bolt pattern when I get home.
  15. HDTony

    I want a C4

    still in the process of building my 65, of course at this stage I decide to make changes, which is typical cause I can never make anything easy. where can I get a good deal, on a nice, hard shifting C-4 to bolt up to a 65 289?
  16. HDTony

    Rearend Swap info - FAQ

    Eaton Trac-loc. is what I put in my 9". pretty sure they make one for you 8" as well.
  17. HDTony

    American Racing wheels walk off....need help!!

    Personally I would call the wheel manufacturer and see what exactly they recommend. they more than likely stock them as well.
  18. HDTony

    Brake lights staying on

    well there is some adjustment, but it involves a file, when I replaced the rod from the pedal to the master, my brake lights wouldn't turn off, I filed the back end of the rod a bit and it loosened up the connection at the switch allowing it to turn off when releasing the pedal.
  19. HDTony

    1966 rearend swap and front disc

    I used the kit from discbrakeswap.com, Dennis is a good guy to deal with. very helpful.
  20. HDTony

    1966 9 in rear end ??

    You can have it narrowed, thats how I did mine, I'm a few months ahead of you doing the same project. I have my 289 sitting here 75% done and my suspension and rear end are all in. the rear end was a lot of work, I have a little over 2K into the rear end alone, but its a 9" narrowed to fit 15x8...
Top Bottom
Back
Forums
Menu