Search results

  1. A

    squeaking/moaning while breaking

    theyre new :-\ maybe 1500 miles/6 months on em
  2. A

    squeaking/moaning while breaking

    recently ive been getting a squeaking or moaning in my right wheel when i slow down to a stop. not everytime, but pretty often. also, when slowing down from a high speed, i get a thump thump thump, almost like a low tire. any thoughts on what this could be? checked the break shoes in the...
  3. A

    borg warner wires (good)

    just got a set of wires, borg warner for my 88. work *great*. idle is still alittle funky, and i have an occasional miss at idle, but im sure thats the cap. theyre a vast improvement over the suckers that were on there, motorcraft i think? definate recommendation.
  4. A

    t5 removal/replacement

    how hard is this to do? my trans finally went. clutch went limp today, check and the linkage appears to be pulling the level on the tranny, so i guess thats it. needed one anyway. but how difficult is it to drop one and replace it, other then obvious tools and a 2 ton jack/jackstands, what do...
  5. A

    is this a sway bar?

    rough measurement reads 1 1/2" for rear and about 1" for front
  6. A

    Im selling my car....

    no no. alarm stickers dont do it. get a big AUDIOBAHN sticker, and like, ALPINE maybe. you also need a whole assload of MOMO stuff screwed, taped or glued to the interior. 100+hp, easy.
  7. A

    Im selling my car....

    i think ill sell my 88 and get a 92 civic, some stickers, and a momo shifter knob/ebrake handle combo. i challenge everyone in this board to beat me. stickers make me go faaassttt.
  8. A

    is this a sway bar?

    in the spirit of curiousity, can someone post a picture of a front and rear sway bar on our cars? preferably stock front, because mine doesnt look as puny as everyone describes. and id be interested to know if it was upgraded.
  9. A

    is this a sway bar?

    hah, positive i dont have a 5.0. vin checks out as a 4cyl too, thought maybe previous owner pulled a 5.0 out. the guy said he wanted to drop a 5.0 in though, perhaps he threw it on expecting to do the swap?
  10. A

    is this a sway bar?

    there is a bar running parallel with my rear end in the back. looks like its bent to give a little, kind of crooked sucker. cant get a pic right now, but is this a sway bar? i didnt think we had them in the back. on the 2.3s anywho.
  11. A

    screwed up stud on rear drum

    many thanks, i just got done and am about to drop it off the jack and take it for a test drive. it was a *bitch* finding lugs to fit though. finally replaced my long ones with shorter ones, but they seem to fit O.K. just a note, it was alot easier tightening that sucker down with the...
  12. A

    screwed up stud on rear drum

    awesome guys. thanks for the advice, i was fine checking the lugs periodically throughout the route. however, i got slammed with 6-7 inches of snow and that slowed things down a bit. why didn't you warn me? :-P anyway. im going to napa this morning as advised and im fairly sure i didnt bend...
  13. A

    screwed up stud on rear drum

    all that and pep boys sold me the wrong damn studs. i slide it in and it fits all sloppy, the little grooved part isnt as wide as the stock ones. man am i pissed. i need my car for my route tonight and im sure everyplace is closed. 7pm on a sunday. what a day. :(
  14. A

    screwed up stud on rear drum

    yeah i realized after i posted that it was there. my mistake ;) youve helped me out a bunch of times with stuff on here, whether you realize it or not, and your site has gotten me out of a bunch of jams. just want to thank you while i have your attention, for the site/the responses/the...
  15. A

    screwed up stud on rear drum

    ps im attempting to do this without screwing with tthe drum brakes, i did once, and it was a bitch to fix.
  16. A

    screwed up stud on rear drum

    alrighty. the thing that has the studs coming through it. i hit one of the problem studs with a hammer once, and it didnt move really, but it appears the "plate" (thiing that the studs come through, flange?) bent ever so slightly.
  17. A

    screwed up stud on rear drum

    i attempted to hammer out one of the studs and it appears the plate bent slightly. whats up?
  18. A

    screwed up stud on rear drum

    going to attempt this with a breaker bar, wish me luck
  19. A

    screwed up stud on rear drum

    what do the studs attach to?
  20. A

    screwed up stud on rear drum

    if only i had wired my compressor up
Top Bottom
Back
Forums
Menu