Search results

  1. K

    $ for an upgrade

    Gots my Gears........YO 3 Bling Blings.......2 Phatty Phats.......and 1 "yo that is whack"!! LOL.........3:73's have been installed. :banana: Wowieee man. They are off the heazy.......fo sheazy = they kick a** man Went with Ford Racing. Cost was 625.00 with loc rebuild. No friggin...
  2. K

    Odd electrical problem...this ever happen to anyone else?

    I had almost the same issue last month. I could not figure it out for the life of me. I had intermittent electrical issues and the whole car would buck when i tried to step on the gas. I also used to have issues starting the car when it was hot, thought it was the starter along with other...
  3. K

    problems with x-pipe install

    I put my BBK Xpipe without cat's on last summer. No problems. Just lots of grutning, pulling and pushing. The metal hooks that are welded to the Xpipe? Do they fit into the rubber hangers no problem? In other words, do they line up or seem short?
  4. K

    Car runs rough at idle, smooth in higher RPMs. If it is shut off, won't start back..

    Are you having any other issues? Electrical or otherwise?
  5. K

    $ for an upgrade

    I currently have 3.27's. The gap between 3.55's and 3.73's I figured wouldnt be much or any at all. But between 3.27's and 3.73's? I will play around with the chart. Thanks Grady
  6. K

    $ for an upgrade

    Good point and thank you Tranny is a stock 5 speed.
  7. K

    $ for an upgrade

    I love Foxwwods!! Bling Bling and a Booya too!! Just got back from Foxwoods casino. Played in a holdem tourney, came in 3rd, won $800. So now I'm thinking it's gear time instead of headers. I did some searching and found most peaople are installing FRPP's. I currently have 3.27's in the...
  8. K

    $ for an upgrade

    After looking at all the post's on pullies verse headers I think I'm going with the BBK headers. I use my A/C often in the summer and the negatives with the pullies outway the positive. I would rather spend the $200 and have a solid upgrade than spend $100 and possibly have issues or only be...
  9. K

    Driver Power seat

    No problem. The only thing that blow's, is now my girl wants to drive all the time. :rolleyes:
  10. K

    $ for an upgrade

    Shorty's I would use with my setup, correct? They are identical lengths compared to stock, correct? I was told by a friend who installed headers on a 95 that he had to Move the A/C or the lines to the A/C around to get them in from above. Do you have any charging issues with the pullies?
  11. K

    $ for an upgrade

    I have about $150 to get an upgrade but not sure what to get. Right now all I have is a MAC CAI, Flowmasters, BBK X-Pipe. Was thinking pulleys or headers or something else. Not to excited about putting headers in if I purchase them. Heard its a pain. Obviously looking for best...
  12. K

    Driver Power seat

    Just wanted to let those people who have an issue with their drivers side power seat what I found in mine. Since I had the car, the drivers side power seat would blow a fuse when I started the car and tried moving seat forward or backward. That also meant I could never use either one of the...
  13. K

    Headlight Switch....Plz Read!

    Hey guys, Replacing headlight switch. Removed the knob and bezel and switch from dash no prob. I am trying to remove the shaft that the knob sits on from the defective switch to put it on the new one?? I'm wondering if the shaft is supposed to already be on the new one?? Thank...
  14. K

    Needle in a haystack

    Finally, Finally, Finally...... I did it! :D I'm all done......Rebuilt injectors, ported upper and lower manifold, new egr valve and gasket, new pcv valve and breather, new battery, new ground cables, new headlight/dimmer switch, new brake light switch. The is the 1st time I have ever...
  15. K

    Needle in a haystack

    Carnage Pix You rock Rio!! Thanks man, I will head over to NAPA after wrk tomm. Heres some pix of me scraping the heads yesterday and then the broken injectors......web page is all screwed up, but you get the point. PIX BTW, is it a good idea to clean the injectors with carb...
  16. K

    Needle in a haystack

    Needle Found........More Friggin Issue's Ok, so, I really think it should be against the law for dumbasses like me to be able to use a wrench. Yesterday was the first day off from work that was sunny since I received my manifold. Started putting the the manifold together. Took me all...
  17. K

    Needle in a haystack

    Finally Suh-weet! Manifold's made it hear today. I have everything apart, cleaned and ready to be put back together. I have a couple of questions that I cannot find crystal clear answers to. These are probably a no brainer questions for most of you. What exactly should I buy for...
  18. K

    Needle in a haystack

    Grrrrrrr So I am still friggin waiting for my Instake to get here. I bought them off Ebay. Dude said he sent them on Wed.. It's been 3 damn weeks without my baby! Anyways. I got the upper manifold off, the MAC cold air intake out, and all wires hoses and connections disconnected, except for the...
  19. K

    Needle in a haystack

    O.K......So I replaced the ground cable on the drivers side fender going to the block with a copper one. Also cleaned up the major ground next to the oil filter. Unfortunately the upper and lower intake I bought wont be here until Thursday. Also replacing oil sending unit, serpentine belt...
  20. K

    Needle in a haystack

    Thanks for everyones quick reply. Tomm. is supposed to be sunny and dry here in MA so I will tackle it then. I will let you guys know what I came up with.
Top Bottom
Back
Forums
Menu