Search results

  1. k00ksta

    NEW MAF Timing Question

    Ok one more thing Ok also when I go to look at or alter my timing at all What steps should I take before touching the distributor. Should I unplug any harnesses or anything. Also Will it matter if I put the motor in TDC I dont really see a reason to considering it will start up and I will just...
  2. k00ksta

    NEW MAF Timing Question

    Thanks for the response Sweet wife will be happy I dont have to dump some more money into it right now :rlaugh: Well from what he told me he just played with the timing to help it run a little better. To be honest I think he was full of :shrug: he also did a crap job in wiring the fans up...
  3. k00ksta

    NEW MAF Timing Question

    Hrmm Ya this is not a broke head gasket been there done that and know what that looks like its not that much white smoke its def. related to the fuel/air mixture because if I plug the stock MAF back in with the current setup it runs fine just of course does the "Floating on a cloud Throttle...
  4. k00ksta

    NEW MAF Timing Question

    No Chip was burnt I think I made a mistake here when I said he tuned it. All he did was time the car to run "better" no chips were burnt, no pcm was altered what so ever. I just had 24# Injectors on this new motor with a calibrated (stock) 19# MAF hooked up. So I think he may have retarded or...
  5. k00ksta

    NEW MAF Timing Question

    I have just finally purchased a Calibrated MAF for my 24# Injectors (Should have went larger but hey) I had the car tuned by a mechanic for the 24# injectors with the stock MAF for awhile and the car ran pretty well other than the floating of the throttle and such. Now When I dropped this in the...
  6. k00ksta

    What cable goes to starter??

    No Problem Great looks like it helped. :D :D
  7. k00ksta

    MAF and CAI Install Question

    Nice thanks After speaking with a few other people I know they told me that the computer may take a few starts to get the correct setup in the computer. And to be honest it makes alot of sense. And from like you said it probably was set to fat and the computer sensed the correct air...
  8. k00ksta

    MAF and CAI Install Question

    Well I just finally got time to drop my Cold Air kit in and my MAF calibrated for my injectors but it seems when I first started the car. It started up perfect seem to be running really rich got alot of exhaust (whitish) smoke from the mufflers for about a minute or so. then that seemed to...
  9. k00ksta

    What cable goes to starter??

    Starter Cables There are 2 wires that go to the starter. They are both 12v. There should be a large red cable that comes directly from the 12v on the battery and straight to the one terminal post of the starter with a nut. then you should have another smaller wire which comes from the High...
  10. k00ksta

    95 Mustang Clutch Switch BY-PASS

    Thanks man Man .. haha you are def the man :hail2: I wont be able to test anything until possibly tomorrow with switching around the relays. this has me so damn bummed haha been thru every wiring diagram and trouble shooting technique I could possibly think of. im leaning towards either an open...
  11. k00ksta

    Pics of my 331 Trickflow build....

    EGR Valve clearance with the valve covers I had to also run a intake spacer to clear the egr valve ears from the valve covers and the upper intake. it would almost sit on top of it. Im running the track heat upper as well and pretty much the exact same motor build as him.
  12. k00ksta

    95 Mustang Clutch Switch BY-PASS

    Voltage Reading Do you happen to know what the voltage reading should be at the starter on the W/PK Wire thats going to the starters Selenoid? I will try another relay today and see if this gives me more juice down below. such a pain in the rear-end. :flag:
  13. k00ksta

    95 Mustang Clutch Switch BY-PASS

    Ok Wiring is correct Ok after fixing that I now have it wired correctly I assume the other connector can just stay open (black connector with BLUE/YELLOW & RED/LT GREY) wires. I think thats something for the Cruise control or something else. Ok Twisted the two you said together also metered it...
  14. k00ksta

    95 Mustang Clutch Switch BY-PASS

    Think I goofed this up Well after looking thru wiring diagrams and my chiltons manual I think I have goofed this up. I think that the Red/White Striped wire should have just jumped down to the other wire on the same connector and not criss crossed. I believe the other connector is for the...
  15. k00ksta

    95 Mustang Clutch Switch BY-PASS

    Ok fella's I think I have wired my clutch safety switch (bypass) incorrectly because the switch is faulty which is causing my car not to start. There are 2 Connectors that plug into the clutch switch and im not sure which wires to butt-splice together to bypass the switch. I basically looked at...
  16. k00ksta

    95 MAF Possible Causing Engine to not Start

    Cool Thanks Ok Will def. Try that I did pull the starter and had it tested but im not sure if htey test both the starter and the solenoid or what at autozone I would Imagine both but who know's Hopefully its just a stuck solenoid and nothing more. And also thanks for confirming that if I...
  17. k00ksta

    MSD coil issue!

    MSD 6AL and BLASTER 2 COIL Ya mines the same damn way and I actually pulled it off the car and went back to the stock ignition system. Because for some reason my battery is also drained pretty hard after 3-4 days of the car just sitting when the msd box is hooked up. so there must be an open...
  18. k00ksta

    wired up fan switches, almost caught the car on fire

    Oh Man You Cannot just run some wire from there fans yo. You got 40 amp's running thru there in high temp as well. The wire rating for that application is about 10-12 Gauge with Teflon Insulation or Silicon. Also you need a 40AMP Cracker Relay in there so you dont have to bring all that juice...
  19. k00ksta

    94-95 COBRA INTAKE ON 347 WOULD IT WORK???

    Do Yourself a Favor If your going to pull the motor and rebuild Just do yourself a favor and ditch them (even when ported) restricted intake and manifold. For the price you cant really go wrong with a nice Trickflo Track heat upper and manifold. Just keep in your mind 1 thing that I have...
  20. k00ksta

    EGR valve hitting FPR, pics inside.....

    On my 95 GT I had to use a http://www.trickflow.com/product/manifoldsandspacers/pr_spacersefi.asp# to clear it. Also Stock hood will still close amazingly its damn tight tho.
Top Bottom
Back
Forums
Menu