Search results

  1. Kurt2002

    FRPP EFI Valve Covers Question

    anyone?
  2. Kurt2002

    FRPP EFI Valve Covers Question

    I have the FRPP Polished valve covers for my AFR 165 heads. Anyone having problems with certain 1.6 RR with these covers. I want to make sure I have no clearance problem with these covers. Thanks,
  3. Kurt2002

    Rear Disc Conversion Kits

    What the best way or kit to get to convert to 5 lug rear disc brakes. I already have the 5 lug axles in and using drum brakes. I want to get rear disc to improve my brake pedal and stopping power.
  4. Kurt2002

    Electric Fan or Not to Electric Fan?

    I'm installing my heads, cam, etc..... next friday and was wondering if I should just get the HD fan clutch or install a electric fan from Flex Fan? I'm putting in a 180F thermostat, Edelbrock Water Pump and FRPP Aluminum Rad. Thanks,
  5. Kurt2002

    Question on my 5 lug install

    I did not change the MC or booster because I'm still using the rear drums. I did not adjust the booster rod. That would help i bet. How many turns do I turn it?
  6. Kurt2002

    Question on my 5 lug install

    I did the sn-95 front spindles and the new FRPP front lower control arms with the improved ball joints and I did the FRPP rear 5 lug drum kit. I put on SS brake lines on the front. Now my pedal goes down over half before braking. I bled the brakes and there is no air. Can I bring the pedal up...
  7. Kurt2002

    Adjusting RR on Stud Heads Question

    I have AFR 165 heads with 7/16 studs, my question is how do I adjust these rockers when I install them? The Haynes manual only talks about the factory setup. Thanks, Kurt
  8. Kurt2002

    Anyone with Bassani Equal Length Headers

    How do you like them and did you tell any improvements in HP after the install?
  9. Kurt2002

    What Size Injectors for AFR165?

    Will my 19lb work with AFR165 head, Edelbrock preformer intake and stock cam? I also have 30lb I cound install. Which would be better?
  10. Kurt2002

    Injectors Question

    Why is 36lb injectors so much higher in price then the 42lb injectors? Is the 36lb different?
  11. Kurt2002

    Think about maybe going from a SN-95 to a Fox, need advice

    1989-1993 LX is your light foxbody. I'm not sure if the hatch or notch back make any difference though. Good Luck
  12. Kurt2002

    Header Question

    Yes they are stage 8, so I don't have to retighten them after I put the locks on?
  13. Kurt2002

    Header Question

    I getting ready to install LT headers and I bought the locks for the header bolts. My question is after I tighten the header bolts do I put on the header bolt locks or do I wait until it goes through a few heat cycles? I don't want to have to retighten them over and over.
  14. Kurt2002

    Stangs parts might of screwed me

    I know and that is what I requested was a 94-95 spindle. They said the box was mark wrong, so I don't know unless someone with a 96 can look for me. Or have 95 spindles on their car and can look.
  15. Kurt2002

    Stangs parts might of screwed me

    I ordered their sn95 5 lug converversion. On the box it had 96 left and the other box said 96 right. I called them today about it and the said the piece where the tie rod connects to the spindle if it is straight then it is a 94-95 spindle, if it was bend it is a 96 spindle. Is this...
  16. Kurt2002

    Crower #15511 Or #15512 Cam?

    with aod it only see 5500 rpm at shifts. So I should be good then, thanks
  17. Kurt2002

    Crower #15511 Or #15512 Cam?

    Good article, very helpful. As far as the questions you asked, the stall is 2800rpm with 3.73 out back. We are planning on using 1.6 rr not the 1.7 rr. Checking p to v clearances what would be a safe zone. I see what the articles says but should I want more or be around what the article states?
  18. Kurt2002

    Crower #15511 Or #15512 Cam?

    will the 1.7 clear the piston tw 2.02 valve with that cam (15511)?
  19. Kurt2002

    Crower #15511 Or #15512 Cam?

    15511 is Duration @ 50 218/224 Lift 1.6 RR .468/.486 15512 is Duration @ 50 222/228 Lift 1.6 RR .496/.512
  20. Kurt2002

    Crower #15511 Or #15512 Cam?

    I helping my friend put on TFS Twisted wedge heads and he wants a new cam for his 92 LX with a AOD. We are looking at these two cams. Would either of these two cams work with Twisted Wedge heads? And which one would be the best cam for a auto with stall converter? Thanks
Top Bottom
Back
Forums
Menu