Search results

  1. Bill88Stang

    How To Run 15inch Welds On A Sn95 Swapped Front End On A 90 Lx

    I still have the stock master cylinder and booster in there as the previous owner did not finish the swap completely. The rear brakes are the original equipment ones that came on the sn95 rear he put in the car. I keep seeing either the 93 cobra master cylinder and booster or the 94-95 cobra...
  2. Bill88Stang

    How To Run 15inch Welds On A Sn95 Swapped Front End On A 90 Lx

    Like it says before you flame me I know not many would agree I'm just asking what I need to change or go back to to be able to run the 15 drag life's so I can do the bigs and little s. It's a 90 lx with a sn95 front brakes up up with the red 95 cobra calipers at all 4 corners. Front brakes are...
  3. Bill88Stang

    Sn95 5 Lug Swap With Cobra 4 Wheel Disc Help

    I just bought a 90 roller yesterday that the previous owner swapped a sn95 front end, sn95 rear into and then was in the middle of installed the old school 95 cobra 4 wheel disc set up in and sold me the car. The calipers are red with the white cobra lettering. My question is can I use the stock...
  4. Bill88Stang

    B303 in a 351w

    No the springs have been upgraded and yea it is a roller block. I know it was small I just wanted to use it since it was free and I do not have to worry about the oils today wiping out the cam. With the 1.7's on it the cam will be jut about the same size at what was in there. I was just asking...
  5. Bill88Stang

    B303 in a 351w

    I know it's a tad small for a 351 but the reason I was leaning towards it was due to the oils today not being very kind in flat tappet cams and I can get a b303 from a friend for free by trading some parts. The motor is .030 over with 10:1 forged pistons, mass air conversion since lightnings...
  6. Bill88Stang

    mass air meter question

    thanks for the info
  7. Bill88Stang

    mass air meter question

    i picked up a mass air meter from a fard van its a 80mm unit out of a 98 e150 van. can i take my stock electorics off my 55mm and put it on the 80mm? i just finished converting my 94 lightning to a 89 a9p mustang computer and a bauman trans controller to control the e40d and its currently...
  8. Bill88Stang

    got bored today

    nice job
  9. Bill88Stang

    pinion depth

    i was looking at that i was just wondering how good the non ford tools worked .
  10. Bill88Stang

    pinion depth

    for those of you that install your own gears what tools do you use to set up pinio depth? ive only used the rotunda kit when i was workgin as a tech at ford since ive felt for better money i dont have access to those tools anymore.
  11. Bill88Stang

    home porting gt-40 irons not the P's

    has anyone found a good write up on home porting the gt-40 irons, all ive found was write ups for the p's but im not sure how close there are and if something that worls for the p will work on the irons as well.
  12. Bill88Stang

    please i need help bad

    its 157 tooth and go to fordracings site they have one , its what i used when i put my 351w in. its sfi certified and just what you need. good luck. so what you need is a 157 28 oz manual trans flywheel.
  13. Bill88Stang

    clyinder head porting

    does anyone knwo any good links to home porting of your heads and intake? thanks
  14. Bill88Stang

    cobra grill insert install

    hey for those of you that have installed one, can i ask how you do it and how you attach it? my wife got me one fro x mas but it didnt come wiht instructions. i cant seem to find any write ups on the internet on how to do it thanks.
  15. Bill88Stang

    stock times for a 95 gt

    yea i figured it woudl be a 15.0 car at the track, he cant drive worth a dam i just didnt wana say do you realize yuo have a 15.0 car and in reality theyll do a mid 14 ya know. i just like having as much info as i can to throw at this guy
  16. Bill88Stang

    What do I need to switch to carb?

    you dont need a tank froma carbed stang persay, you can have a sump welded into the bottom of your stock tank or just put in a fuel cell thats another route. i went with the sump in the stock tank. youll need some sort of ignition box like msd or a cheaper route would be a duraspark box from a...
  17. Bill88Stang

    trak-lok rebuild

    not bad at all, remove s spring, remove spider gears, remove side gears which hold cluth pack in place. soak new clutches in friction modifier(as ford tells me to do at work), reinstall, the hardest part really is sometimes just getting the s spring back in thats it. but theres a tirck to it...
  18. Bill88Stang

    stock times for a 95 gt

    hey guys just curious if you can enlighten me a bit. im curious as to waht time a stock 95 5 sp gt will run? i work wiht this redneck moros with a beat up 95 gts that is positive he will take my 88. i know its not possible i just want to know waht it will run stock, i thinking low 15 maybe...
  19. Bill88Stang

    stock times for a 95 gt

    hey guys just curious if you can enlighten me a bit. im curious as to waht time a stock 95 5 sp gt will run? i work wiht this redneck moros with a beat up 95 gts that is positive he will take my 88. i know its not possible i just want to know waht it will run stock, i thinking low 15 maybe...
  20. Bill88Stang

    Help Help Need B303 Cam Card Specs Please

    what are you trying to do ? ive never seen the specs for the ford cams anyother way then there listed on the site
Top Bottom
Back
Forums
Menu