Search results

  1. BullittStangV8

    bouncing needles on new gauges

    Do they have a good ground or share the same ground?
  2. BullittStangV8

    New Patriot heads?

    Heard the quality sucks and the castings were inconsistent. Just word of mouth over at hardcore50.com
  3. BullittStangV8

    Flaring Fuel Lines & Fittings. NHRA legal ?

    Truck, Thanks for posting that part number and picture. Summit caries them, and Ill just pick one up with a bunch of other things I need from them. Thanks for the help. Ill post some pics of the finished product when I can.
  4. BullittStangV8

    Hooker Headers, good/bad/ugly

    Ratio, You are forgeting however, that cooler, denser gas flows slower. Higher gas temperater (higher kinetic and potential energy), woud allow for higher exaust flow speeds, if that is what your point is. Also, by keeping the heat inside of the header, you are decreasing engine bay...
  5. BullittStangV8

    Thoughts on Demon carb?

    Call Prosystem Carbs. Tell them your set up, and what you want, and they will at the least give you a suggestion for a carb that will best suit you. You can make a request online on their website, and they email you a response with what carb they feel will best fit you. They did not even push...
  6. BullittStangV8

    Flaring Fuel Lines & Fittings. NHRA legal ?

    I know the limit is 12''. The issue is that I am using rubber hose from the tank to the line, and the distance from the firewall to the pump makes a total distance over 12'', or real close to it. Also, for general safety, I would rather use only braided lines in the engine bay.
  7. BullittStangV8

    Hooker Headers, good/bad/ugly

    I have Hooker super comps and they are great. I had to "reshape" one of the tubes slightly to work with a roller block and a z bar kit. However, they worked perfectly with my old 289 block, and they have not rotted in 8+ years at all.
  8. BullittStangV8

    Flaring Fuel Lines & Fittings. NHRA legal ?

    Truck, I see what your saying now about the earls fitting you used. The fitting I have uses a rubber washer and a compression sleeve type of set up that seals on the backside of the flare to a male -6 an fitting. With the set up I have, I would need to flare the fuel line. Do you have a link to...
  9. BullittStangV8

    Flaring Fuel Lines & Fittings. NHRA legal ?

    Truck, Thank you for pointing out that the image I had shown was wrong. The fitting I actually have is the earl's one that you mentioned. I was not sure if a 37 degree flare was needed for a 45 degree flare. I have -6an line ran from the fuel pump on. Anyone have any suggestions for a flare...
  10. BullittStangV8

    Flaring Fuel Lines & Fittings. NHRA legal ?

    Guys, I have a 3/8th SS hardline ran from my tank to my engine bay. The issue I have is the limit in length rubber line that the NHRA allows. So, I need to run SS or some other legal hosing from the hardline to the fuel pump. I guess the best option is to flare the hardline, and then put a...
  11. BullittStangV8

    Opionins on Mach I exhaust project.

    Magnaflow magnapacks. I've had them on me Bullitt, as well as my 03 cobra, and I love them. The packs are much louder, and louder at idle then the magnaflows. I currently have flowmasters on my 65, but the are getting cut out, and some dumps are going to be run.
  12. BullittStangV8

    331 Supercharged...?

    66forfun, you make some good points there about drivetrain goals. My car has been down for 3+ year because stock components just dont go well with performance parts. I grenaded my original 289 block (bent the valves, ect. and did enough damage to the cylinder walls that the block was trash). I...
  13. BullittStangV8

    Electrical problems are not sexy

    Did you run the power wire near a speaker wire?
  14. BullittStangV8

    331 Supercharged...?

    FWIW, I went with a DSS pro bullet set up. It has: Level 10 CNC Block Main Support System Extreme X Forged Pistons Forged I-Beam Rods Nodular Iron Crankshaft Moly Rings ARP Main Studs / Rod Bolts Fully Race Balanced & CNC Blueprint It makes right around 420 flywheel HP...
  15. BullittStangV8

    331 Supercharged...?

    Forged crank? I have not heard of many cast/non forged cranks breaking. Usually its rods/pistons. Also, you probably will split the block before you would snap a crank. Also, flowmasters kill hp compared to straight through mufflers. If you like the sound, then go for it of course. Any reason...
  16. BullittStangV8

    If anyone is interested my 66 Fastback build site.

    What hood? and how was the fit?
  17. BullittStangV8

    Disk brake kits

    Yeah I got in contact with him through the email account. Everything is fine. Thanks guys.
  18. BullittStangV8

    Disk brake kits

    How did you guys order from Denis? His website doesn't mention a way to order, only to contact the email address.
  19. BullittStangV8

    summit hose

    I know this probably won't help, but I used summit braided hoses with no problems.
  20. BullittStangV8

    What can I use from a 96 mustang in a 67 rebuild?

    The seats. (the front, and the rear with some modifications. )
Top Bottom
Back
Forums
Menu