Search results

  1. 88Stangboy

    Steering Wheel Vibration

    Hmm, thats what i was thinking, but wouldn't you hear it tapping against it? Unless its pressed up against the shaft pretty hard, catch my drift? I would make sure all my bolts, etc were tight and in place, sounds to me like stuff is really loose down there. Probably a combination of...
  2. 88Stangboy

    Electric fan ?

    Thanks, thats what i was looking for. Out of all the systems on a car i know the least about wiring to tell you the truth, but im learning quite a bit. Im going tomorrow to pick up a book or something about wiring to help me along, and i have alot of diagrams, etc.
  3. 88Stangboy

    Electric fan ?

    oh, i have a relay. Its just the wires are to thin of gauge, they are getting warm and so is the switch, the relay is fine. Its the wires and switch that are warming up, etc. And the connectors at the switch, the plastic was melted on them. Its an accident waiting to happen as i said and im...
  4. 88Stangboy

    Electric fan ?

    ive had a 3G, the guy before me wired the fan with wire that is much to small. And the toggle switch is in-adequate also, when the fan is running you can feel it heating up, etc. I wanna up grade the switch and the wiring while my dash is out. And im going to run a fuel pump cut off switch as...
  5. 88Stangboy

    Electric fan ?

    What gauge wire to use to properly rewire my electric fan. I am taking my dash out to rewire some of...well everything, but what gauge wire should i use to rewire my electric fan, its an accident waiting to happen. The guy before me used some wire that is much to small for the fan, its run off a...
  6. 88Stangboy

    power diff between H and X

    What would it sound like if you cut the crossover out of an H-pipe? Probably like ****, but just wondering.
  7. 88Stangboy

    now lower to the ground

    my car is lowered 2" and i have pretty bad bump steer, but i have skinnies up front also. Im raising it back to stock ride height. I've traded paint with about every speed bump, high driveway, pothole in town. Not worth lowering it to me. Traction went down the drain to. My car came that way...
  8. 88Stangboy

    Having starting issues, Too much accessory load?

    Thats the same prob im havng now. Like tonight, i was at pizza hut, i drove my mustang because im trying to wear the new tranny in. Well, i stopped at the bank to get some money from the atm and cut my car off while i did it. I went to start it and it hesitated a minute and then cranked fine...
  9. 88Stangboy

    what carb????

    I would just smooth them out gently, dont make the ports any bigger. Gasket match it and use a carb spacer if you have the hood clearance. Other than that, those flow pretty good out of the box for a street car. As far as polishing it, just take some red scotch pads and go over all the ports...
  10. 88Stangboy

    need ur advise fast

    TRACTION! Your friend is going to need a hell of alot of it! The STI's wouldn't be to much to beat if they didn't grab so damn hard, The one my friend has grabs so hard it'll knock the hat off your head! Its crazy how damn hard they grab in each gear, you can launch them at 6,000 and only...
  11. 88Stangboy

    carb starting problem

    Agree'd, lots of overlap can cause a car to be hell to start when its cold.
  12. 88Stangboy

    Engine Ground question

    Thanks, ill try that one. When i finally get time to actually spend 10 minutes working on it, busy, busy, busy :bang:
  13. 88Stangboy

    Alternator question

    Yep, V belt. Thanks for that wiring diagram. I upgraded to a 3G and i never upgraded the engine ground, it has stock grounding, etc. That may be where most of my problems are steming from. Im definatly not an expert on electrical, but im trying my best to learn. Thanks for all your help, its...
  14. 88Stangboy

    Engine Ground question

    Yea, ive had this problem for the last few months, ran the codes last may and nothing came up, i was like damn. I mean, its just annoying as hell, i have dumps so every little fart and burp can be heard and its annoying and the lack of power makes it no fun to drive either. Where is the best...
  15. 88Stangboy

    Engine Ground question

    Its not really consistant, it comes and goes, mainly when you just jump on the throttle hard. it goes crazy. I do really need to go through my grounds and make sure they're all ok like you said. Thanks
  16. 88Stangboy

    Engine Ground question

    I posted this in my other thread also....sorry... But i was just simply wondering if the engine ground isn't sufficiently connected,if that alone could cause a mis-fire condition? Ive had this bad, re-accuring mis-fire condition for about 5 months now and its starting to just piss me off...
  17. 88Stangboy

    Nasty screeching noise at start up!!

    Agreed. But before you torque it down, take it off the bell housing and look the gear over on it. If the teeth are chipped up or some are missing, replace it. My buddy had a starter gear that was so eaten up it wouldn't even turn the flywheel over. All the teeth on it were worn down and broken...
  18. 88Stangboy

    if i put on a blower, will the stock tranny need to be replaced soon?

    just baby it around and save up for a tremec. If you run it, its going to break. With stickier tires and a grippier clutch it'll break sooner, just take it nice and easy. Dont get on it, it only takes once to mess up a sycro or bend a shift fork, then your screwed. In fact, buy the tremec...
  19. 88Stangboy

    WHAT THE HECK controls the idle in these things?

    Yea, i had the same problem with it sticking to. Try that.
  20. 88Stangboy

    5spd rattle in 3rd gear - ideas?

    I have the same problem and my tranny is freshly rebuilt, only 50 miles on the clock. Rattles lighty in 3rd and 4rth. Isn't leaking, i am going to check the mounts, etc.
Top Bottom
Back
Forums
Menu