Search results

  1. boss_302

    foldown seats interchange?

    hello all can anyone tell me if the fold down assy from a 69/70 fastback will fit into a 67 fastback.thanks javed
  2. boss_302

    66 mustang fastback, like no other

    hello kermit you over here too (GT350)
  3. boss_302

    67 Shelby tail panel w/no cutting?

    here you go check this site out http://www.mustangproject.com/Catalog.aspx?category=68642387-6653-4218-935e-89619ca5f35a&sub=f238e982-267e-40ef-96d5-47cd6aad2b01
  4. boss_302

    Cobra Rear Discs on 9" Housing

    very nice work:nice: will you be making anymore brackets ? If so let me know i plan on putting rear discs on my 67.regards javed
  5. boss_302

    Ron Francis -Feedback

    I got the mustang kit. In the kit there is a metal plate with 2 holes with heavy duty grommets,this is held on the bulhead with 4 screws,The only connections i didnt have were for heater switch/motor and wiper motor which i made my own.Regards javed
  6. boss_302

    Ron Francis -Feedback

    I just wired my 67 with a ron francis express panel and can only say good things about it.Its very easy to work with and tech support was always on line when needed.regards javed
  7. boss_302

    wanted pair of 69/70 mustang doors

    looking for a pair of nice rustfree doors for 69/70 mustang just need the doors.regards javed email [email protected]
  8. boss_302

    Post Your Stang!

  9. boss_302

    Shelby/Eleanor Trunk Fiberglass

    http://www.stang-aholics.com/ these guys are the best for fibreglass kits for shelbys.regards javed
  10. boss_302

    cant get gears toploader

    There is freeplay in linkage and i have took the adjusting rod off and moved the clutch fork by hand to see if it makes contact with press plate and it does.
  11. boss_302

    cant get gears toploader

    The bellhousing runout is ok,if i start the motor press the clutch i cant put it in gear.If i put it in gear and crank the engine the car will move even with the clutch down any ideas ,i personally think the pressure plate is stuck.regards javed
  12. boss_302

    cant get gears toploader

    Hello, just managed to get my car fired up after a lengthy rebuild,67 mustang 4 speed toploader centrforce 2 clutch,hurst shifter.My problem is i cant put it in gear when the engine runs.I have adjusted the linkage to take up slack.Any ideas ? all the clutch stuff is new.Thanks javed
  13. boss_302

    any engine gurus out there?

    thanks thanks guys all running sweet an quite:nice:
  14. boss_302

    any engine gurus out there?

    I done what the shop manual said .Is there a different procedure with roller rockers do you tighten the hex nut then the allen headed set screw inside the big hex nut.regards javed
  15. boss_302

    any engine gurus out there?

    The clickety click sound, i have a 70 boss that sounds the same thats why i thought i might have a solid lifter cam they are tight no wiggle i checked again and have a couple of loose rockers which i adjusted and tightend according the shop manual that would also explain the backfire i have thru...
  16. boss_302

    any engine gurus out there?

    Yes i primed the engine before i fired it up its been stood for 3 yrs with me.The previous owner i got it off didnt do the work on it .It was done before he got the car.Regards javed
  17. boss_302

    any engine gurus out there?

    Just managed to fire my motor up.Its a 351w with dart cast iron heads,singleplane intake,holley,my ? is about the roller rockers how can i tell if they are for solid or hydraulic cam they are erson 1.6 and are fitted with an inner allen key type lockscrew.All this motor work was done by someone...
  18. boss_302

    gas cap part where to buy?

    hello pete is there anything else that i can use like a slimline twist on cap i think will be alot safer ,just need to find one that fits inside the pop-open cap like the one in the pic any help would be appreciated.thanks javed
  19. boss_302

    gas cap part where to buy?

    hello all im in need of the sealing assembly that seals a pop-open gas cap.The piece that seals the cap to filler neck is missing where can i buy replacement.See pic below,its the whole assy i need the spring/rubber gasket and retainer bolt.he Thanks javed...
  20. boss_302

    Currie rear Cobra brake conversion brackets for 9 inch

    im doing the same what would you use for e-brake cables? regards javed
Top Bottom
Back
Forums
Menu