Search results

  1. G

    Tubbin?

    hey ,, i found a book with mini tubs in it ,, is that what you looking to do?if so ill find the book , and give you the www.site...
  2. G

    hyd roller question

    i live herr in br la. so cam motion is 5 miles from me .. i want a stock type idle though get this my 362w 10.7 to1 , solid roller spec's > 242/252 at .050lift was .601/.585 edel rpm heads rmp intake 750 v sec carb FMX trans with 3.27 posi.....this set up got 12mpg all high way...
  3. G

    hyd roller question

    yes i got no link bar...i had a 362w in my 83 f 100 it threw a..well 3 rods,, so iam building a 408 with 9.5to1 ,, cam is undecied... for now . i got edel rpms im going to reuse..there not hurt.. i might just go solid roller again.. low lash like i had b4 it got taken out by the rods...
  4. G

    hyd roller question

    ok.... i got a 91 351w block non roller block. i got factory hyd roller lifters and hold down brackets from 94 351w roller block. my question is..if i use the above stuff on my 91 351w block. i will need a special made cam for the 91 w block? .. i think the base circles different...
  5. G

    need to borrow a 03 cobra lower crank pulley

    Rpm outlet told me that i install it wrong ..how the hell you install it wrong . they didnt even give me ful credit back. restocking fee ,,,like what they going to do resell my old one .. they suck i never order from them ever again..total *******s there.......dont go thought all the stress i...
  6. G

    k member issue's???

    i just got stock 17x9 up front im thinking of AJE does but the ft. tire way up in the wheel weld ? i e mail AJE but never got a reponse >? been 2 weeks now . what a way to run a bussiness?
  7. G

    k member issue's???

    i would but i need one that will accept the stock susp. etc .like stock a arms, and springs, ans is not going to put my front wheel farther forward? my 83 gt has a ground pounder unit . i had to cut ft lower fender for whell to clear. i dont wont to cut my 03 fenders .
  8. G

    k member issue's???

    i need a stock k memebr for my 03 cobra , i found a couple ok ? ford said any k member made after 9-18-00 to a 04 will work on my car. i found one off a 2000gt. thats fairly close to me.but the guy dont know the build date ? whats the dfference between the 99 and newer ones? . i found a 03 cobra...
  9. G

    wtb stock k member for 03 cobra

    i rather not say where . or who. :nonono:
  10. G

    03 Cobra Lower Pulley help

    i had ported eaton with 2.75 upper 9.0 lower 6 lbs i had 20 psi dropped to 17 during the pull , i had 490 rwhp and 576 rwtq. but i took off the 9.0 lower and but stock lower back on , i was throwing belts due to the cheap moto blue brand i had. iam sure other name brand did not have this...
  11. G

    wtb stock k member for 03 cobra

    but why is that always on a forum ? most of the time iam typen fast and dont have time to check spelling .look i dont care if iam uneducated, iam 41 and been out of school for some time.i been working on cars sence i was 15 . yes i didnt grad high school , i finshed voc tec. auto mech's .i had...
  12. G

    wtb stock k member for 03 cobra

    am banned from there.. people made fun of my grammer.more than 1. so i let them have it .i didnt know you needed to knoe grammer on a forum? its not like am getting graded? and what does grammer have to do about haven a mustang? its not like am e mailing the president.:D for a job.
  13. G

    wtb stock k member for 03 cobra

    i didnt get my recall notice . gas pedal got stuck at the wrong time.hit a raised manhole cover and hit a fire hydant. im depressed , i finally getting over whip lash. the ft end where the k member mountd is pushed back 1/2 to 1 inch and bowed in about the same . underneath the car where the...
  14. G

    Any idea what stock rods are in an '01 Cobra

    there cracked caps rods ,made of pressed powder very weak indeed.pistons are not much better.
  15. G

    wtb stock k member for 03 cobra

    i cant seem to post in classifieds , or cant ask questions? i need a stock x member pm me please . i wrecked my car and need one bad. thanks :nice:
  16. G

    anyone know the part numbers for these IRS mounting brackets?

    looks like upper subframe mounting brackets , but i seen them call all diff names for things. tommorrow ill get the part#s off mine it raining its butt of right now.or id go see.
  17. G

    03 cobra dyno results!!!good or bad?

    did you get it from rpmoutlet? did they take it back? what lb lower did you have?
  18. G

    4.10's?

    3.55s all you need i see people runnin3.27s even in the top ten shoot out cars with auto's
  19. G

    Pulling motor..

    see on compressor or ps pump on motor. layed to the side .
  20. G

    Pulling motor..

    heres going back in with intake on. here pulling with intake off.
Top Bottom
Back
Forums
Menu