Search results

  1. Foxfan88

    installed fabricated box upper.

    lol alot of my friends made the same comment on it looking like a coffin. it was originally a rectangle shape but i went back and made the plenum smaller.
  2. Foxfan88

    installed fabricated box upper.

    got around to finally trying out the upper box i made for my setup. i was worried about it killing low end. but suprisingly the car feels the same down low. and it may have picked up top end i am not too sure, if it did its not a huge difference. i didnt take and exact measurements but i...
  3. Foxfan88

    havnt posted in a while.

    sweet man, let us know how it goes.
  4. Foxfan88

    Should I sell my MSD 6al?

    definatly keep it. when i had my vortech on the car, and started running 12-13 psi after i upgraded my heads and cam. the stock ignition couldnt even fire the engie at high RPM. after like 4k it would just cut out real bad, reducing the plug gap helped but didnt cure it. put an ignition...
  5. Foxfan88

    Replacing pick-up?

    access to a press makes it alot better. on the dizzys ive messed with, the gears like to get STUCK pretty good on the shaft. you may need a press to get it off. as for the pin. when putting it back in, MAkE SURE you get it on right, the hold in the gear and shaft ARE NOT in the center of the...
  6. Foxfan88

    INJECTORS AND FUEL PRESS.

    most injectors are flow rated at a specific pressure. alot of them (mustangs) are are 39 psi. you set the base FP with the regulator with the vac line OFF. this simulates the atmospheric pressure at WOT. whatever you set your base fuel pressure to is what you should see at WOT (...
  7. Foxfan88

    overheating issues

    if the car cools correctly at highway speeds (more than enough airflow) but heats up at lower speeds. you have an airflow issue. if your car gets hot even at highway speeds. you have a coolant flow problem. whether it be the Tstat or a blockage or something. did you do something to the car...
  8. Foxfan88

    Mob's project thread

    there is a bolt in the ECM plug that you need to loosen before the plug will come out.
  9. Foxfan88

    few questions, motor related.

    ive been down this road. get some aluminum heads the first time around. if you dont have the cash, then just save for a while. its not too hard to save up 1000-1300 dollars for some nice heads, TW heads work awesome IMO. if you get the ported e7s or gt-40s etc etc and are serious about making...
  10. Foxfan88

    If you had a stock 5.0?

    for the money nitrous will get you faster for cheap. then a power adder and then the HCI parts. i personally reccomend the power adder. will make alot more power than a HCI and can be as cheap as a HCI or maybe a tad more (but the power you have over the simple HCI justifies the cost)...
  11. Foxfan88

    What is up with this Typhoon intake?

    actually its a copy of the performer RPM
  12. Foxfan88

    Factory MAF Mod ?

    you would need to get the computer also to effectively use the meter. if your tuning the car through the EEC though, it doesnt matter.
  13. Foxfan88

    lifting engine and tranny w/o load levler

    ive done it both ways i and say take the tranny out first then pull the motor. you have to get under the car to unbolt the tranny crossmember and etc. 4 more bolts and you can pull the tranny from the bellhousing. that way you dont to tilt the engine real high to get it out with the trans...
  14. Foxfan88

    hooray for pic whoring!

    yeah the new building is done, there isnt any lighting or power but i am able to still work on the car still. if i need any power i will run a extension cord from an outlet where we will tie into the power. i will be able to do the engine part of the deal. once i get that running and all...
  15. Foxfan88

    hooray for pic whoring!

    coming pretty good. i am fixing to build the setup hopefully in the next few weeks. but first i have to pull my motor out, i seemed to have sucked something up as the oil pump is locked up and it broke the intermediate shaft, and i lost oil pressure. i got the broken shaft out and tried to turn...
  16. Foxfan88

    hooray for pic whoring!

    car looks sweet jason, keep it up!
  17. Foxfan88

    kenne bell or procharger

    for a street car i'd say a KB would be a good choice. sure the no intercooler is a drawback but i wouldnt be super worried about that unless your running alot of boost. if you have the PC or vortech, pullied for 10 psi of boost at redline, your going to PEAK 10 psi, so what happens is...
  18. Foxfan88

    Pics of my new DD!

    awesome fox. i like the idea of keeping it mild. maybe a set of wheels or something to set it off. and a gear swap to get some more ooomph. also.... distributor boot FTW:nice: thats when you know its really stock lol, that and the plastic coil cover.
  19. Foxfan88

    New Fast and Furious

    we went and saw it this weekend, i liked it, alot better than the others. and the fact there was a fox in the movie rocked :nice:
  20. Foxfan88

    What's the story with your 'stang?

    i used to be hardcore into video games and computers back when i was in high school. never really had an interest in cars. in 2004 when i was 16 i was at my cousin's house, his buddy had a black 90 GT. i dont know what it had done but i think it had alot of bolt ons and etc etc. i remember it...
Top Bottom
Back
Forums
Menu