Search results

  1. G

    High idle after long drive?

    I dirve my car 45 min's to my local track. I use the criuse. Sometimes when I let off the gas and hit the breaks the car still idles at cruise rpm. Kinda like if I had a carb with a sticking choke. Do I have a bad sensor somewhere? :shrug:
  2. G

    Car backfires when shifting.

    The car backfires when I powershift or speed shift at high rpm. I have played alittle with fp & timing. I have made no changes sence the car was tuned. I run mac exhaust with a prochamber dumped 2 1/2".
  3. G

    What hurts this combo most?

    I still havent cc'ed them they have been shaved.How much I dont know. They were bought bare when they were new. Yeah , I need springs the heads were set up for a solid roller that had over .700 lift.
  4. G

    Need to bore my block how much is 2 much

    I have a 85 351w block that I want to run on the street. The block has been rebuilt & bored .020 once. I think it would need to go to .040 to clean it up.How much of a bore is too much for a mild 500fwhp 410 or 414w?
  5. G

    What hurts this combo most?

    Should I mill mi vic jr's? I bought them used but in current form they flow 200 300 400 500 600 700 int 130 188 237 264 273 267 exh 102 140 162 178 184 190 Will this be fine for a 5 spd car I mostly only to the track? I knew I...
  6. G

    What hurts this combo most?

    95 gt 351w, 9.1 comp dish pistions, GT-40 x303 heads 64cc, heads too small for trick flow 351w intake intake ports, crane h-286 cam,I want to make some changes. I have stock bottom end truck rods with good bolts. I feel the heads are the a bigger prob than the comp ratio. Should I just...
  7. G

    How can I get around the shift retard?

    ON 94-95 cars with a t-5 the eec has a retard built in to make the tranies live longer. Has anyone looked under the dash at the different clutch petal switches? Do you think I can just un plug a sensor that goes back to the computer?
  8. G

    EFI 351 guys I need advise.

    I have a 357 I think I might have a wiped cam lobe. I want to go roller. I have stock rods and crank with good bolts. I now have gt-40 x heads and even though they are ported I think they are restrictive. I kinda thought AHR 185's were right. But don't have a clue on the cam. I drive the car 2...
  9. G

    Need cam & head advise on 357

    I had some bad luck here lately. I think I wiped a cam lobe. Im getting a ticking noise that changes with rpm on one side of my heads. I re adjusted my rockers and it didnt help. I currently have a small .508 .512 with 224 231@50 flat tappet. Im running a tf 351 intake ,gt-40 x...
  10. G

    need info on throttle body's dont laugh

    Most of the dyno books I have read showed a 65mm t/b out performed larger 70&75mm t/b on even 347 strokers.
  11. G

    subframes or not ?

    I installed a 6point roll bar that is welded to the car ar six points .Do you think I still need subframe connectors?
  12. G

    Cam Help

    Common I know there is someone out there who can help. Is a Isky 292 mega cam with 538lift and [email protected] too much for a street car that is 3500lbs and has 3.37 gears with a manual. I am going to run a 351 with x heads with lots of port work done 10-1 pistions.
  13. G

    Anyone know alot about a bumpstick?

    If you can help on my cam Q please reply to Am I too big I need to do something fast.
  14. G

    I've turned into a ricer... dont hate me

    Kinda looks like it needs to shave now but will look cool with those wheels.At least its not gray!
  15. G

    strut tower brace help

    Steeda has one made for the 351 block. Never seen it.If you find out I/M me I need one too.
  16. G

    Am I Too Big?

    I bought a 351 with x heads worked pretty well. It has around 10-1 compression. The problem I have noticed is maybe my cam is just totaly wrong. The motor came with a intake that didn't fit the heads and a 750 B/G speed demon. I have decided against the carb. I bought a Trick Flow EFI...
  17. G

    Everyones favorite game!!!

    Whats your favorite sub-frame connector and why. Have you only used that brand? What is the difference on a convertable & coupe? [B][SIZE=1]
  18. G

    pulley swap bracket?

    Do I need a special bracket or spacer on my 351 swap on my 95 vert. I think the acc. will just hang on the heads right?
  19. G

    Need a/c delete help

    Hey guys , Is there anyone who has just taken the ac compresser off and put a shorter belt on instead of paying $60 for a ac delete? T :lol: his is a 94 95 question only.
  20. G

    center line daggers

    I'm tired of cleaning my billet wheels anyone have a good idea how much it should cost to have them cromed or anidiozed??? What are some ideas. I'm not getting new wheels! I just want to know about adding a different finish. :nonono:
Top Bottom
Back
Forums
Menu