Search results

  1. Deece

    Dugan Viper Hood

    Did you contact Tom at Dugan? I needed a Dugan whale tail and he was willing to pull out the old molds and make one for me.
  2. Deece

    Can we get a vert thread?!?!

    I can get some int shots later this week. I am just about ready to fire up the new motor and after that I have a nice set of blk leather seats with silver inserts out of a 99 that will be going in.
  3. Deece

    Can we get a vert thread?!?!

    Here are a few of mine I need to get some new ones but its like 15 degrees here and shes still up on blocks.. Good news is the 351 is in should be fired up tomarrow.
  4. Deece

    convertible seatbelt question

    Yes the 90 93 ones will work with a little modification. Same thing in my car. Previous owner did it so I cant quite remember everything but I think the lower part was mounted to the inside of the rocker panel. It looked like he cut out the mount from the other car and welded it into mine. I...
  5. Deece

    a/c delete question (vac line)

    Thanks thats what I was looking for, I saved almost all of the diagrams Too.
  6. Deece

    a/c delete question (vac line)

    Anyone?
  7. Deece

    Who makes the best blackest black paint?? Anyone....PPG, DUPONT,Sherwin Williams???

    Straight black no tint added to it. Buddy of mine runs a body shop and said that was the blackest he could get it.
  8. Deece

    a/c delete question (vac line)

    I pulled most of my A/C off when the motor came out and am wondering if I can pull the vac line that goes into the firewall. I believe it controls the dampers on the A/C but am concerned if it also controls the heat. Anybody have any info on this? Its the small hard line that goes in near the...
  9. Deece

    Possible 86gt vert purchase, what to check for?

    run the top up and down a few times look to see if it binds at all or is smooth. The seals will look worn if they are. If you can get your hand on the pump. Its behind the rear seat between the top of the rear shocks. you should be able to get to it from the back pretty easily. Check for...
  10. Deece

    Is there a How to For A/C removal

    Does anyone know if the vac line going into the firewall can be disconnected with the rest of it?
  11. Deece

    Are 7.5 axles interchangeable with 8.8 axles

    Yes they are the same just pay attention to the legth of them
  12. Deece

    Who has MAC 1 5/8 longtubes?

    I had an old INCON kit that required it they were ust two flat pieces of metal one about a 1/4 inch the other less (you can use the same for each) and all you did was loosen the mounts off the k-member and slide them in they were about 4x4 inches ea with a notch for the bolt to sit between...
  13. Deece

    Who has MAC 1 5/8 longtubes?

    I had a set of the 1 3/4 Mac longtubes, fit was decent no problem with my stock starter or the steering shaft. However with the vert motor mounts those things are going to be LOW.... My car is lowered a little over an inch and the collectors are only like 5 inches off the ground.. They would...
  14. Deece

    where to get door shells?

    79 door swill work on an 86 with 79 door panels (or custom ones) the handles are just low on the door. The vert doors have the mirrors in the corners they are off an 87 not gt but mouldings are quite easy to change. I am in the UP of Michigan. please PM me anything further as I don't check in...
  15. Deece

    4cyl to 5.0 conversion tach problem

    Should be a switch on the front of the tach under the gauge bezel. Its marker 4 6 8 realign it
  16. Deece

    help me I.D. this rear end

    The all knowing orb has spoken:nice: I wish I knew about the mpv rotors before I sold my other Turbo coupe rear
  17. Deece

    where to get door shells?

    I have a set of vert doors that I'm not using. I don't think there is ant rust on them, I also have a set of hatch doors but they are off a 79 with the lower door latches
  18. Deece

    help me I.D. this rear end

    Turbo coupes were 4 lug. Measure the distance between the axles, measure the size of the rotors as well little bit of research and you should be able to figure it out also what gears are in it. Also if it is a T-coupe rear you won't be able to find rotors that are five lug with the right hat...
  19. Deece

    Cam recomendation

    Hey guys, I need some help selecting a cam for my motor, I have a couple in mind but I could use some guidance. Here's what I have so far 71 351w .30 over forged pistons -13 dish gt40 y303's (box stock) 1.6 rockers comp mechanical roller lifters efi c-4 with 2400 stall 3.27...
  20. Deece

    c4 trans install question

    This is going to sound retarted but is it possible you have the flexplate on backwards? If its flipped over it would sit about an inch off
Top Bottom
Back
Forums
Menu