Search results

  1. KHibbs

    Made a little walk-around video

    Sweet looking Fox! The engine bay looks very clean and well laid out. If it is dirty, I can't tell from the video. Hope you get her out on the road soon!
  2. KHibbs

    Anderson Valve Covers

    I didn't realize that they are alum and could be polished. I did some work similar to your intake for the intake on my GTI years ago and it came out great. The only challenge was it needed to be cleaned and polished often. I am not sure how much access I will have under the GT40 intake but...
  3. KHibbs

    Anderson Valve Covers

    Thanks for the feedback. The LX I recently acquired is about 99% done in my book so I was thinking of maybe going to these valve covers to replaced the stock ones that were painted but are bubbling/peeling a bit. Not a necessity item but something I may put on the "wish list". KHibbs
  4. KHibbs

    Anderson Valve Covers

    I am thinking of upgrading from the stock valve covers on my 306 and really like the look of these Anderson covers. 1. Valve Covers They don't look like the come with hardware but I figured I would post up and see if anyone had had experience with them. Thanks, KHibbs
  5. KHibbs

    What did you do for your Fox today?

    Nothing too exciting but I did an inner tie rod. A little research on Stangnet, borrowed the tool from Autozone, and the job was a snap. I was actually surprised at how easy it was. :nice:
  6. KHibbs

    Photo of your first Fox Mustang

    It only took 19 years for the the two us to come together. The car I always wanted in high school except now it includes a blower. I think she is going to be around for a long time...:D
  7. KHibbs

    My 88 GT budget build...Project Garbage Pile

    Looks great and nice work in the engine assembly. Did you do anything else to the motor or just strip it down to the block/rotating assembly and then put everything back together? Very cool build and thanks for sharing... can't wait to see her run. :nice: KHibbs
  8. KHibbs

    The official "How many miles does your Fox have?" thread...

    about 107K on the clock now. Only +/- 2K on the new motor.....;-) K
  9. KHibbs

    After along time away, It's time 4 another Fox!

    I just finished a 4+ month search for a really clean fox. Most of what I found up here in New England was hacked up or had taken a real beating from 20 years in this environment. In the end, I went South and found a really nice car. I think I got pretty lucky as finding the right buyer is...
  10. Imported Item

    Imported Item

    Custom front door panels with MB Quart speakers
    • KHibbs
    • Media item
    • Comments: 0
    • Album: 1992 Mustang LX
  11. Imported Item

    Imported Item

    Dyno Tune Session - 421 rwhp / 415 rwtq
    • KHibbs
    • Media item
    • Comments: 0
    • Album: 1992 Mustang LX
  12. Imported Item

    Imported Item

    Built 306 with Vortech S-Trim V2
    • KHibbs
    • Media item
    • Comments: 0
    • Album: 1992 Mustang LX
  13. 1992 Mustang LX

    1992 Mustang LX

    Photos of my 92 LX
    • KHibbs
    • Album
    • Comments: 0
  14. KHibbs

    Just picked up a clean 90 GT

    Congrats Congrats on the new purchase. Sounds like a nice find but I'd really need to see it before I could make any recommendations for first mods... :lol:
  15. KHibbs

    Post your favorite pic of your car.

    Flavadave4 - Nice shots !! Both of them.....:nice: The nice weather is just rolling in here in MA so I hope to get some good shots this spring/summer but here is my best to date. I just pulled it out of the garage on a half decent 40 degree day in March to go for a spin. I'd only had...
  16. KHibbs

    Droooooooooooooone @ 2000rpm + muffler ???'s

    I have the Bassani exhaust in my lx with cats and it has a serious drone around 2K which is tough with 3.73s b/c it means that is right at 40 mph in 4th and between 65-75 in 5th.....:notnice: I just got the car and need to figure out what my options are because an hour or two on the highway...
  17. KHibbs

    How Did I Do At The Track ?

    Sharad - cool write up and thanks for posting it. Sweet Fox btw...:nice: KHibbs
  18. KHibbs

    Hanging Idle with Vortec ... I think I'm close

    EXCELLENT...thank you. I read that a week or so ago (so I know I didn't have to be at .98 or .99 for the TPS) but I must have forgotten the part about testing the TPS was in there. I will test the TPS this weekend and hopefully cross that off the list as a possible culprit. I am...
  19. KHibbs

    Hanging Idle with Vortec ... I think I'm close

    I haven't gone through all of the notes in the link that jrichker posted so I may be jumping ahead and this info is in there but... The TPS is set at .916 volts and the idle is steady at about 950 so I assume that it is working properly. Is there a way that you can test the TPS or the IAC...
  20. KHibbs

    Hanging Idle with Vortec ... I think I'm close

    I'm confused about the answer of the ecm being programmed to do this from that factory as I remember stock 5.0s from the past that didn't do this. I've also read that there can be an issue with a pressure release valve from the Vortech... that is why I posted the Vortech in the post title...
Top Bottom
Back
Forums
Menu