Search results

  1. J

    Timing question

    What should the timing be on a 306, 30 lbs injectors, 75mm throttle body, 75 mm maf, bbk longtubes, performer rpm intake, gt-40 heads, ford motorsports x303 cam, roller rockers?
  2. J

    .30 bore head gaskets

    are the same head gaskets used on a .30 bore as stock? if not does anyone have some part numbers/brand names for .30 bore head gaskets?
  3. J

    Pushrods damaged

    not sure if they were hardened some components of the engine were done before i bought the car. what would be a the correct way of adjusting the guide plates?
  4. J

    Pushrods damaged

    Took my engine apart today and a few of the pushrods are severely worn about 3/4 inch long right near where the guide plates are. Was is bad rocker adjusting that would cause this? Any suggestions welcome. i can post pics if requested. Also how much play should there be in my timing chain...
  5. J

    Help I am Burning Oil...New Motor

    Does any one have pictures of homemade VC baffles? i am experiencing the same problem and i think i may need to make one.
  6. J

    Just started rebuild tonight

    Just started tearing my car apart tonight i had a bad knock coming from the bottom end not sure what it is yet but hopefully i will have it out tomorrow and figure out whats wrong. Im thinking while its all torn up about putting an elec fan, some pulleys and header wrap. Has anyone pulled...
  7. J

    knocking sound

    just changed the oil it was a little bit low seems like its coming from the top as far as i can tell. not so much as a knock but i very loud tick pretty sure its not exhaust because i just fixed a leak and this is a different sound. im just looking for some comments before i tear into it. where...
  8. J

    knocking sound

    My mustang hasnt been drove alot the past few months and i just fired it up and took it for a ride and noticed a knocking sound. the gas was only about 2 weeks old and its 93 octane so i dont believe its detonation but, i cant tell exactly what the noise is sounds like its coming from the...
  9. J

    84 SVO Shifter

    Is the hurst shifter out of the 84 SVO mustang any good? Is it comparable to the comp plus model? I am thinking of purchasing one and can get it very cheap. thanks
  10. J

    Installing A/F Ratio Guage

    what is a wideband and after you find out your a/f ratio how do you go about adjusting it?
  11. J

    keyless entry

    just need help in general the instructrions seem quite overwhelming. any suggestions would be helpful. what type of factory door lock system is it to begin with a 3 wire ground swtiched signal, 3 wire ground switched 2 step, 3 wire positive switched or 3 wire switched 2 step?
  12. J

    fixing a stock tach

    My stock tachometer went out it just sits at 3000 rpm at idle then goes up when i start going. is there any way to fix it. i know the stock tach isnt that accurate to begin with and im strapped for cash but i dont have the money to buy a monster tach. thanks
  13. J

    keyless entry

    i bought an audiovox keyless entry system for my car, has anyone installed one of these or any keyless entry and can give me some pointers/tips? thanks
  14. J

    trick flow 10.4mm sparkplug wires

    im looking at buying a set of trick flow 10.4mm wires but one of the wires was burnt so it was replaced with an 8mm wire. will this affect anything? is it not good to run different size wires.
  15. J

    performance chip?

    Is there anyway to tell if you car has a performance chip in it or if the computer has been tuned? Where would the chip be plugged in? Not sure if the guy i bought the car from had installed one and if it is messing with my mods. what chip would compliment my modifications? can i buy an...
  16. J

    noisy rockers

    that could be but on other modified stangs they just dont seem as loud, i know the x303 is not a very common streeter cam though so maybe thats the case
  17. J

    noisy rockers

    i have 1.7 roller rockers on my mustang and they seem rather loud. are they suppose to be a bit louder than stock? if not how can i fix them. what is the correct method for adjusting them? thanks
  18. J

    Heater Core Replacement

    My heater core has gone bad on my 97 gt and i was wondering how hard it would be to replace it myself or would you recommend taking it to a shop?
  19. J

    Pro-M to K&N

    Thanks for the help i think im going to order one right now
  20. J

    Pro-M to K&N

    are these filters comparable to K&N? i just hesitate because the K&N company is a well known and trusted company
Top Bottom
Back
Forums
Menu