Search results

  1. 65wildstang

    Anyone got a Mustangs to fear headliner for coupes?

    I have been looking at the headliner also. I purchased one of there consoles and as soon as they get the door panels available for the 65-66 ,i will be ordering them. I discussed the headliner with Rick and the way he talked, it was a easy install. They diffently look nice.
  2. 65wildstang

    wheelhouse - How do you clean?

    I used a grinder with a 3M paint & rust stripper wheel. It is black in color & is a very hard sponge looking material. It worked very well as i ended up using the 3M disc to strip the whole underside of the car to metal. There may be some type of chemical stripper that will work, but I haven't...
  3. 65wildstang

    1968 DOHC 4.6 Coupe Project

    The car & gaps look awesome. Its going to be a sweet ride for sure. What engine & drivetrain is he going with? Also , have you decided on the engine management? Beautiful car, keep up the good work.
  4. 65wildstang

    65 mustang polished tailpipes

    Thanks for the pics, i think they look good below the valance. I contacted summit racing and they wouldn't do a special order since they dont stock them. Contacted Jegs performance and they would have to special order them also. Flowmaster will have to bend some up the next time they run them...
  5. 65wildstang

    65 mustang polished tailpipes

    I contacted summit and they are suppose to be finding out if they can get just the pipes. Eleanor 350, on your 65 does yours come through the rear valance or below it? You wouldnt happen to have a picture you could post would you? Thanks
  6. 65wildstang

    65 mustang polished tailpipes

    Thanks for the replies. I will contact flowmaster and see if that is a option. I already have there 40 seriies w/ turndowns before the rear axle installed. I need to finish running the tail pipes out the back soon. Thanks again.
  7. 65wildstang

    65 mustang polished tailpipes

    Is there a supplier that offers the 87-93 type polished tail pipes for the 65 mustang? Been doing a search for the last couple of hours with no luck. Any help would be appreciated. Thanks
  8. 65wildstang

    For sale: C4 & 2500 stall

    Sorry. Trans already sold. Thanks
  9. 65wildstang

    Plastic Front valance panel

    Check ot Mustangs to Fear - Eleanor Body Kits, Custom Interior Parts and More! . I have been told there products are pretty much sraight bolt on and guaranteed to fit. Good luck
  10. 65wildstang

    Hard clutch pedal

    I had the same issue when I completed my t5 conversion. I installed the king cobra clutch setup, and added the mustang steve quadrant to the stock pedal. I tried adjusting the cable and was unsuccessful. It never felt correct and was ridiculously hard trying to depress the clutch. And you could...
  11. 65wildstang

    Dead in the Water...'67 Electrical Problem...

    When you unplug the plug at location 14289 & 14401 on which side is the wire bad? Have you tried removing the wire from the coil and checking voltage with ignition switch on? The schematics look like power is coming from 16a and is pigtailed to 16b at the plug connection. There is a resistor...
  12. 65wildstang

    Hoodpin decisions

    They're around $85.00 a set. Just depends where you purchase them. I also found them on ebay for a resonable price. Talked with a few people about them, and are used alot in the motorsport field. Some people actually use them for door latches also. What i like about them is there smooth when...
  13. 65wildstang

    Hoodpin decisions

    Has anyone ever used the aerocatch brand hoodpin setup AeroCatch® - new design of bonnet pin, available in locking or non-locking versions – see how it works......... ? I have installed a fiberglass hood and fabbed up my own radiator support. I done away with the stock hood latch and need to...
  14. 65wildstang

    For sale: C4 trans & 2500 stall

    Yes I still have the trans. I'm located in TN
  15. 65wildstang

    For sale: C4 & 2500 stall

    here some pics of the trans & convertor. Thanks
  16. 65wildstang

    For sale: C4 & 2500 stall

    Yes, the bellhousing is with it and I will get some pictures for you tomorrow. I will try to add them to the post. Also, I can email you the pictures if you could pm me your email address. Thanks
  17. 65wildstang

    For sale: C4 & 2500 stall

    I had this trans professionally rebuilt and a transgo shift kit installed. It includes a 2500 rpm continental stall that was also purchased new. I had this setup behind my windsor and decided to go with a t5 for the overdrive. Trans may have 200 miles on it when removed. I have close to $1200...
  18. 65wildstang

    For sale: C4 trans & 2500 stall

    I had this trans professionally rebuilt and a transgo shift kit installed. It includes a 2500 rpm continental stall that was also purchased new. I had this setup behind my windsor and decided to go with a t5 for the overdrive. Trans may have 200 miles on it when removed. I have close to $1200...
  19. 65wildstang

    3.8/auto swap into 68? Possible?

    I have an ECU from a 95 or 96 3.8 mustang if interested. I can't remember right of hand what model. Let me know if interested or needed. Thanks
  20. 65wildstang

    Wilwood Master Cylinder

    Builder of high quality hydroboost brake systems Check out this site. They have a large assortment of rod ends that should work for your setup. Good Luck
Top Bottom
Back
Forums
Menu