Search results

  1. K

    Front suspension rebuild

    I was at my local Mustang parts shop and I was talking w/ the owner about rebuilding my front suspension on my 65 v8 coupe. I explained I wanted to rebuild my front suspension w/ new rubber bushings and he explained I would need more than just the bushings. He explained my A-arms would need to...
  2. K

    Short Yoke for 9" Axle w/ drive shaft Q?s

    I just got my 66 Stang back on tires, off the jack stands and her a$$ out of the air finally. I did a 77 Lincoln Versailles 9" swap and last thing to do is figure the driveshaft length. I'm running a C4 currently and will upgrade to a T5, someday. Whenever I go a T5, I will order a new...
  3. K

    Mustang Sagging Driverside Rear

    What torque is recommended on the rear shackles?
  4. K

    gas tank

    My 65 tank came from here also and the price was right!
  5. K

    What to expect to pay for a 4cyl fox

    I know off topic but the 2.3 forum has little active threads. My wife absolutely hates the fox body style and I just love it, wanted one since high school. All of our current cars are v8 cars, so I'm kinda playing w/ the idea of buying a fox 4 banger as a daily driver for little $. Whats...
  6. K

    9" 3rd member from yard w/ good ratio?

    Lots of good info here. I will just keep my eye open for deal on a Bronco section w/ a trac-loc 28 spline or 31. I also was able to find some 28 spline side gears on ebay and I think I can proably tackle swaping these gears w/ everyones help here. My jeeps Dana 44 & 30 is were I think I built...
  7. K

    9" 3rd member from yard w/ good ratio?

    Wow!! Sounds a bit over my head. I was hoping it would be just as easy as buying a center section w/ a desired gear ratio, pulling my 28 spline axles which I just spent about $200 on having new bearings & studs pressed on (materials & labor), removing my current center section, bolting in the...
  8. K

    9" 3rd member from yard w/ good ratio?

    There are plenty of full sized broncos being parted out in my area. I'll keep my eye open for a trac-loc w/ 3.50's. I plan to stay w/ the 28 spline axles as I want to keep expenses low. So from my understading the track-loc and gears are interchangable between any 9" correct???? Thanks!
  9. K

    9" 3rd member from yard w/ good ratio?

    FYI, I haven’t posted for a while but have been slowly working on the stang!!! I have replaced the rear springs, rear frame rails and trunk floors added a new fuel and I have wire wheeled 1/3 (the back) of the undercarriage and painted flat black. The front 2/3 will have to wait till spring...
  10. K

    anyone bought anything from LAUREL MOUNTAIN MUSTANG

    I purchased a fuel tank, price was good, I priced on ebay and called to place my order. Customer service was good but the salesmans knowledge was slim (young guy). I would buy again.
  11. K

    Need welding wire advise

    Super thanks! I just needed someone to confirm this before I go an purchase more wire.
  12. K

    Need welding wire advise

    Ok, so my dad taught me to arch (stick) weld about 10 years ago and I haven’t welded much since. I got a $200.00 craftsman wire feed welder 110V about 3 years ago and barley used it, now I'm installing new frame rails and an entire new truck floor in my 65 and I have ran out of the wire...
  13. K

    Rubberized Undercoating

    I plan to repair my bad rust, then wire wheel the entire underside, spray a rust encapsulator, prime then coat w/ flat black and call it good. My car will likley see little rain/snow.
  14. K

    Rear frame rail replacement 65 coupe tips

    My rails came w/ the holes for those big heavy hangers pre-drilled w/ sleeves for cross bracing, is this what your refering to? Thanks!
  15. K

    Soft Pedal Bad Performance

    Yea, thats what I did considering they are not hooked up, I also didn’t fill the rear brake reservoir in the master. Wakeboarden, please post the solution when you figure it out as I have my coupe up on jack stands fixing some rust issues and it will be a while till I address the brakes, thanks.
  16. K

    Soft Pedal Bad Performance

    I have the same problem after installing the Scarebird front disc swap. Pedal to the floor w/ little braking but I have nothing hooked to the rear as I'm in process of doing a 9" rear axle swap. I have not had the car on the road for a while and wont for at least 6 months. I have just been...
  17. K

    Rear frame rail replacement 65 coupe tips

    I was in the process of installing a 9" axle & new leafs in my coupe when I discovered my rear frame rails are part rotten, so I have purchased a new rail patches and plan to pull the gas tank this week, but would like all your tips and experiences before I install the new rails in a coupe weeks...
  18. K

    Is the 8" yoke interchangeable w/ the 9"?

    Is the 8" yoke interchangeable w/ the 9" or will I have to source once somewhere. I'm getting closer to pulling the old 8" and intalling my rebuilt 9"!!!
  19. K

    70 Mach one rear disc brakes

    Post some photos of the brakets, I'm currently working on a 70's Lincoln Versailles 9" rear and I know may others here have also, good luck!!!
  20. K

    Whats a fair price to sell my old 8"

    Whats a fair price to sell my old 8" axle to a local hobbiest? All stock w/ lots of miles.
Top Bottom
Back
Forums
Menu