Search results

  1. T

    Viper-spec T56 installed... what gears?

    I need to snap few more pics.. Yes, I reused the factory transmission mount from my T45.. ;) All of that for 2K.. :)
  2. T

    Twin stock pumps?

    Ah... I knew there was a catch.. ;) Thanks..
  3. T

    Viper-spec T56 installed... what gears?

    3.27's with a Viper T56.. is a DOG.. 1st gear is decent.. all the way out to 55mph.. but, 2nd just doesn't feel good at all.
  4. T

    Viper-spec T56 installed... what gears?

    Well.. I guess 4.30's it is!
  5. T

    Twin stock pumps?

    I've been debating fuel pumps for a while.. Today, I got to thinking.. The stock pump is good to what? 300-325whp? Why not run dual stock pumps? 600-650whp worth of fuel is plenty for most people.. And a stock GT pump should be easy/cheap to get ahold of...? Am I missing something here?
  6. T

    Viper-spec T56 installed... what gears?

    What kind of RPM are you guys turning up with 4.30's in 6th, and 70-80mph?
  7. T

    Viper-spec T56 installed... what gears?

    Even with the taller gearing in the Viper T56?
  8. T

    Viper-spec T56 installed... what gears?

    Got my T56 in.. and my Novi 2000.. This thing is a DOG with the stock 3.27's. I've got a set of 4.10's I'm thinking about tossing in.. Should I go taller/shorter? I'm thinking that the 4.10's will be sweet with this trans/blower combo.. Travis
  9. T

    Heavy vibration at speeds about 50 mph. What could the problem be?

    Check your driveshaft.. make sure you didn't loose a weight..
  10. T

    Question about C&L 95mm MAF..

    Right, I understand the MAF scale table concept.. I just haven't had a chance to "real world" or even bench test this MAF to see the limit with the increased diameter of the tube. Funny that you say Nissan MAF.. I build Nissan high perf. parts for a living.. Maybe a twin turbo Z MAF would work...
  11. T

    Question about C&L 95mm MAF..

    Anyone?
  12. T

    Question about C&L 95mm MAF..

    I recently purchased a Novi 2000 setup for my '00 GT from a fellow in Florida.. He advertised that the setup came with a 95mm C&L MAF/55lb Motron injectors. After recieving the kit, I noticed that the MAF screws were loose. I looked at the part number, and found: F6UF-12B579-AA From my...
  13. T

    Started on my T56 swap..

    I swapped out the triax shifter handle for the stock piece.. and it's MUCH quieter.. I think I'm going to leave it like this.. It still has a crisp shift with the Triax base.. but, there's much less noise transmitted into the cabin with the stock shifter handle. It's kinda wierd at 70mph, only...
  14. T

    Started on my T56 swap..

    Well.. I started her up tonight.. after getting my driveshaft shortened and the Cobra yoke swapped over.. I took it out on the highway, and it runs great.. however, I have a slight chattering noise at idle, with the clutch engaged and the trans in neutral.. It only happens when I rev the engine...
  15. T

    t56 6 speed swap in a 01 GT

    I just finished up my T56 install into my 2000 GT.. I didn't have to beat in the floorpan at all.. or modify much of anything.. I even reused the T45 crossmember, by sliding the plates with the attached nuts back, an inch or so.. Everything bolted right into place, and the install took...
  16. T

    Started on my T56 swap..

    Trans is in! The trans crossmember is temporary (until I get the Cobra piece in).. But, honestly, it fits fine, and I'm sure that the 2 bolts would be ok for a while. I should have the right one in next week.. so, I'll swap it out when I get it in.. The only snag that we ran into.. was...
  17. T

    Started on my T56 swap..

    haha... nice.. I didn't realize that you were on this forum. :) I don't think the people here are ready to "accept" a Sentra with a Maxima engine in it, yet.. ;)
  18. T

    Started on my T56 swap..

    I'm waiting on my transmission crossmember, and I have to modify the driveshaft that they gave me.. the flange/knuckles are larger.. and won't fit on my rear end. Travis
  19. T

    Installed XE270AH

    Sounds like there's excessive valve lash..
  20. T

    Installed XE270AH

    That definately doesn't sound right... what is that rattling sound? What was the lash set to?
Top Bottom
Back
Forums
Menu