Search results

  1. 67coupestang

    The Reenmachine DOHC '67 Shelby Clone Convertible Progress

    awesome car!! I have a dumb question about the rear end. What does it use for upper arms? I only saw the lowers and struts. are the halfshafts supposed to act like an arm? and also on that note with inboard brakes... what happens if you snap a half-shaft?
  2. 67coupestang

    Intake Installation

    get 4 bolts, to fit the block, longer the better. cut the heads off then carve a slot in the top for like a flat head screwdriver. install them loosely then use them to help drop the intake straight down. unless u get the cork ends with the sticky side to help hold them, just use rtv...
  3. 67coupestang

    Disc Brakes

    just kidding i checked no fittings. but i did run new lines to the block on both sides. they had the standard ends on them and they're screwed right to the rubber 73's
  4. 67coupestang

    Disc Brakes

    i used the 73 hoses on mine, but i dont remember using any adapter fittings :( and im too lazy to go the garage this second. i'm taking it out in a bit ill check in later :D
  5. 67coupestang

    Whole lotta pressure... what gives?

    is this a plastic overflow? squeeze it and see if its full of pressure. did you replace the radiator cap? the cap acutally controls boil over more than the mix i think. water has a higher boiling point at greater pressures. i.e. when the cap is holding it in. sounds like its almost wide...
  6. 67coupestang

    Backfire

    mine backfires every year when i pull it out of storage. bad fuel it usually clears up after carb cleaner, new fuel and about 30 miles for me
  7. 67coupestang

    windshield polishing

    My windshield has a nasty haze to it from schatches making it really difficult to see out of at night. Anybody have any experience polishing theirs?? I was thinking of trying some simple polishing compound and a rag, I dont have a power buffer. Anybody know if this is a service that an auto...
  8. 67coupestang

    66 sedan delivery?

    definately WAS a fastback. no way in H#$% thats original. I highly doubt that color was on cars in 66 and look at the glass in the back. looks more like the back window from a broncoII or something not a 60's design
  9. 67coupestang

    T5 oil

    i use syncromesh in my tremec 3550 great stuff... expensive (especially if you forget to put the speedo gear back in and you puke it out) but smooth
  10. 67coupestang

    What tool to cut out floor pans?

    sawzall all the way. i used a black and decker navigator, worked, but a sawzall would have worked great
  11. 67coupestang

    clutch cable conversion- brake push rod length?

    http://www.mustangsplus.com/Merchant2/merchant.mv?Screen=CTGY&Store_Code=MPFMP&Category_Code=push try that one
  12. 67coupestang

    this WAS a 67

    F-U-G-L-Y!!!
  13. 67coupestang

    Shelby front apron, legal?

    Oh thank god! The uptight and anal po in Clear lake Iowa, gave me crap about a front plate on my 76 bronco. I live near albert lea minnesota now. I wouldnt put one on a shelby style valance anyways, they can write me a ticket... Now in minnesota all i have to worry about is the $120...
  14. 67coupestang

    Some more EFI swap info needed.

    The fuel pump relay is run off the computer, not directly off the ignition switch. Thats how you get the "hold the key on, fuel pump runs for 3 seconds, then crank". Dont know about any battery warning light, but hav you considered using a 3G? I had problems keeping up with all the fuel...
  15. 67coupestang

    using a car dolley

    I used a dolly to bring mine up from waverly, towed great behind my 4.0 liter explorer, no problems, removed the rear d-shaft, capped the tranny and away i went. 2 years later i get a tandem axle from u-haul and haul it again to albert lea with my v-8 expo, towed like a pooch, wanted to sway at...
  16. 67coupestang

    Crate '69 Camaro soon Crate '67 Mustang FB?!

    i came across the place that sells the fiberglass fastback bodies, nice but I dont know if i"d do it for road racing or even daily driving... too much to crack. http://www.usbody.com/WhereQualityComesFirst.htm
  17. 67coupestang

    What's the correct install direction for slotted rotors?

    yours are on right same type principal with the cooling vanes, they need to pull the dust away from the center
  18. 67coupestang

    Strut suspension

    I'm gonna TRY to use a fox body front strut, and keep it front steer... Strut suspensions suck for handling compared to unequal length double wishbones, but this is my DD, and if it sucks too bad i can always add upper arms and re-engineer later...
  19. 67coupestang

    Best Looking Mustang (non stock) Pics

    i like how the cide scoop is silver and how it blends in the front fenders
  20. 67coupestang

    Best Looking Mustang (non stock) Pics

    yea preston's is fugly but it looks just like an imsa racer and is built just like and imsa. If i knew what the underpinnings of that red one were I might respect it more...
Top Bottom
Back
Forums
Menu