Search results

  1. roush 97

    i cant get my factory radio out

    Do the lx's have the graphic Equilizer like my gt did under the radio? If they don't you shouldn't need an install kit. Your new radio should fit right in there.
  2. roush 97

    i cant get my factory radio out

    Do ya got the radio removal tools? Or is it the wiring holding it from comming all the away out.?
  3. roush 97

    How to get wax off?

    Get some Meguiers paint cleaner, that'll take it off, but you'll have to wax it again when your done.
  4. roush 97

    gas mileage

    I get about 24 mpg highway with stock gears. City it can drop to 17 or 18 if I really keep my foot in it. Still better than my 6 banger Ranger that gets about 14 or 15 no matter what..
  5. roush 97

    Air Induction Recommendations...

    Would I see any gains if I upgraded the TB, MAF, and put on an open airbox system? I got the mods listed below. Not planning on spending the money for a new intake for now. What brands do you guys recommend for parts that would eventually work with a new intake when I decide to go that route.
  6. roush 97

    Light Switch...

    Heck, I didn't even think of 5.0resto. I got there catalog around here somewhere and I think there in it. Thanks.
  7. roush 97

    Light Switch...

    Can I still get a headlamp switch through Ford or somewhere else, or can it be fixed? I shut my lights off and now the parking lamps and dash stays lit up. I pulled back hard on the switch and they shut off, but the slightest little bump they come back on. I pulled the fuse for now.
  8. roush 97

    Leaking antifreeze

    I had the same problem. I changed my water pump thinking it was the weep hole. Still leaked. I cleaned up my engine really good. Looks like it's comming from behind the timing cover. On top of the cover there's a valley between the water pump and head on the drivers side of the car that...
  9. roush 97

    stang cleaning day, tips please.

    I usually wash with Kit car wash, the yellow stuff. It's amazing. I think it has a bit of wax in it, that's why the car really shines after I wash it. I use the Meguires products to clean, polish, glaze #7, and then wax #26. Then if I feel like I wanna really make it shine I top it off with...
  10. roush 97

    ? about A/C clutch

    If your just replacing the clutch, I don't believe you have to depressurize it. Other than that, I haven't chenged just a clutch, but the previous owner of my car did right before I got it. If nothing else, this is good for a bump.
  11. roush 97

    Lets See Those Stangs!

    Here's my '91
  12. roush 97

    push vs pull

    My guess would be best pulling. You put it in front of the radiator it would have to be run more and faster, other wise , if it were off it would block airflow imo.
  13. roush 97

    Test pic

  14. roush 97

    Storng exhaust smell

    Check your header to H pipe bolts. I started to get that smell and mine worked loose. I tightened them back up and no smell.
  15. roush 97

    fors are gay

    Me too. :lol:
  16. roush 97

    fors are gay

    So what, every Winston Cup car, Busch series car and Craftsman truck series truck runs a FORD 9 " rear. SO what's your point? Wasn't for a Ford pushing the Dodges, Dodge would never win.
  17. roush 97

    Window screetch

    Window screech What do I need to lube? When I roll either window up or down, they screech really loud. It gets annoying. Thanks for the help.
  18. roush 97

    AMp wiring questions, for power source.

    I wanted a bit more punch to my speakers so I hooked my amp up to them. I wired the remote turn on up to where it's supposed to go on the back of the reciever. I hooked the constant power up to the battery, (I used a fuse link at the battery too). Well, the amp works fine, till I start the...
  19. roush 97

    Got caugh for my exhaust, 160$ ticket, need help guys!

    So that's why people lower their cars. Hmmmm
  20. roush 97

    Rearend Bearing removal Question?

    More than likely as when I did mine, I ended up pulling the center race of the bearing and the rollers that were in the bearing were everywhere. I went ahead and pulled the outter race, then I took a magnet and fished out all the rollers that got in the axle tube. I rented a slidehammer from...
Top Bottom
Back
Forums
Menu