Search results

  1. G

    Centerforce Dual Friction Clutch

    Has anyone here tried a McLeod Street Twin Clutch? I'm trying to decide between the RAM Street Dual Clutch and the McLeod Street Twin clutch. One advantage to the McLeod is that it can be purchased with a 0 oz imbalance (my crank is internal balance) where as the RAM would need to be special...
  2. G

    Centerforce Dual Friction Clutch

    Hmm, I'm will be running: 351w 408ci Stroker AFR 205cc Heads Flowtech Induction Custom Cam 850 Carb Victor Jr Intake 1 3/4" Headers Either 2.5" or 3" Exhaust I was thinking about a RAM Dual Friction clutch, b/c they say they can withstand an excess of 900 ft/lbs and still provide...
  3. G

    Centerforce Dual Friction Clutch

    Does anyone know the holding capacity on one of these, all I can find is 90% Greater Holding Capacity, but what does that really mean? I'm looking for a number horsepower wise.
  4. G

    1 3/4" Headers with cable clutch

    Does anyone here run 1 3/4" headers with a cable clutch? I'm running a mustangsteve cable clutch kit in my '65 coupe with a 408w hooked up to a TKO 600 with a lakewood scattershield. I have a mustang II front suspension so clearance to the sides won't be a problem with no shock towers, but I...
  5. G

    65 Mustang Doors

    Zookeeper or any of you guys in the southwest, could you keep a look out for me for a nice set of 65-66 doors, maybe check craigslist or the local paper and see what you can find? I've pretty much exhasted my resources here in St. Louis, Missouri and haven't found anything at all. Yesterday I...
  6. G

    65 Mustang Doors

    My driver side door is full of bondo, and my passenger side door is caved in around the door handle. Should I buy door skins and replace the sections of the doors that are bad, completely reskin the doors, buy brand new repo doors, or try to find original doors (no luck so far)? The door lines...
  7. G

    Custom Camshaft

    69gmachine: What is your opinion on your aluminum flywheel and 3" Magnaflow stainless exhast? Would you go with a steel flywheel or 2.5" exhast if you had it to do over, or do you like the setup? I'm currently contemplating both.
  8. G

    Insulation inside new door skin

    You should try Lizardskin Ceramic Insulation. It's a spray on insulator/sound deadener. http://www.lizardskin.com/
  9. G

    Custom Camshaft

    '65 Mustang Coupe TKO 600 Tranny 9" Rear End with 3.50 gears
  10. G

    Custom Camshaft

    I guess I should go into more detail about my particular component selection for my engine package: 351w Stroker 408ci ~9.5:1 compression AFR 205cc Heads Edelbrock Victor Jr Intake Manifold Not sure on carb yet, but perhaps Edelbrock 750cfm-- is this undercarbed? Mechanical Roller Cam...
  11. G

    Custom Camshaft

    I'm currently Camshaft shopping for my 408ci 351w build and I am considering a custom camshaft from Flowtech Induction. Has anyone dealt with them before? I've been dealing with Ed specifically. What is everyone's opinion on a custom camshaft vs. a factory cam such as Comp Cams. I'm planning...
  12. G

    Rolling my fender lips

    You can rent the tool if you don't want to buy it. I'm not sure what the website is, but you just pay to rent the tool and shipping both ways. I'm sure someone on here knows the place, or you can try searching the forums for a previous post about it.
  13. G

    351 stroker kit.

    Stroking a 351 to 427 puts much more stress on the engine. They say that the maximum dependable cubic inch 351w stroker is 408. When you stroke the engine to 427 it puts the piston rings real deep in the cylinders which increases wear on the engine b/c of the oiling. It might even cut the...
  14. G

    Rod & Customs New Rear Coil-Over System

    It really doesn't look so great to me.... but it is bolt on for whatever that counts. Looks like a very weak design though.
  15. G

    picture of the underside of a 65 mustang

    Yeah, get a chiltons.
  16. G

    six with a v 8 sound?

    Yep, do a v8 swap if you want v8 sound...
  17. G

    Insurance wants me to find a body shop in sandiego for the 67' poor baby :(

    How do you back into something as pretty as that??
  18. G

    How To Install A Door Skin

    For all of you guys putting skins on your doors, how well do they line up? I'm worried that an aftermarket skin will ruin the lines on my '65.
  19. G

    So much for the first day out at the track...

    Misery, I mean Missouri.... What a wonderful state.... I hate the weather here.
  20. G

    TKO 500 in a 65

    To get the right driveline angle on a 65-66 the transmission tunnel will need to be raised.
Top Bottom
Back
Forums
Menu