Search results

  1. N

    Got my 4cyl conversion running. Have a few questions

    yes the small wire is on the solenoid. Also I used the 1993 V8 harness and computer. The starter is out of a 1990 but I used the 90 wire that connect the starter to the solenoid and again the car does start by jumping it, just with no key.
  2. N

    Got my 4cyl conversion running. Have a few questions

    It has been almost 2 years since I started the project. The car was a 93 4cyl auto, and it now a 306 with a tremec 5spd. I did not drive the car there is no driveshaft in it. I wanted to just start the car before I got it back to 100 % in case I had to fix something else. Anyway I turned the...
  3. N

    73' Belt for No A/C and no smog supposed to fit but wont

    72.5 fit. Dont ask me why. The 73 was supposed to fit. They also make a 72.8 and one other size too. These are goodyear belts.
  4. N

    73' Belt for No A/C and no smog supposed to fit but wont

    yea stock pulleys
  5. N

    73' Belt for No A/C and no smog supposed to fit but wont

    I mean the belt is too big.
  6. N

    73' Belt for No A/C and no smog supposed to fit but wont

    I found the diagram that says I am supposed to use a 73' belt with my Ford a/c delete bracket and not running a smog pump. The belt goes around but seems loose. Anybody know if there is a way to tighten the tensioner more or do I need a smaller belt? I am using this diagram, but the belt is...
  7. N

    How long will the oil pump stay primed?

    I manually primed my oil pump about a month ago. Since then I have installed the distributor, etc. How long will that prime hold before it need to be reprimed? Thanks.
  8. N

    What size bolt for EGR delete in cylinder head?

    Thank you
  9. N

    What size bolt for EGR delete in cylinder head?

    I know I can buy these plugs from a vendor but does anybody know what size bolts I can fit into the back of the cylinder heads to plug the egr ports? I will remove the tubes but behind them is threads that screw into the head.
  10. N

    Big Problem with GT40 Intake,Tall Valve Covers PCV

    it is the tubualr GT40 intake. I amy have to try and grind the "T" Here is a pic on the T that runs under the intake manifold to the PCV. Sorry for the quality its a phone pic. I would say I have less than 1/4 inch between the valve cover and the intake. Can I plug this T and reroute the...
  11. N

    Big Problem with GT40 Intake,Tall Valve Covers PCV

    The pcv fits in the back of the manifold. Its where the lines go into the bottom of the upper intake. There is a T fitting that will not fit into this application. The lines come from the pcv into this T fitting and then into the upper intake
  12. N

    Big Problem with GT40 Intake,Tall Valve Covers PCV

    I just checked I have the 1/2 spacer. I know they make an 1 inch spacer but I am really not sure that is going to do it. It is in an unmeasurable spot. Could I run 2 spacers? I have a cowl hood so clearance should not be an issue. Any suggestions?
  13. N

    Big Problem with GT40 Intake,Tall Valve Covers PCV

    ok I ran into this today. GT40 intake with Moroso Tall valve covers. I have a spacer under the manifold already. The manifold will clear the valve covers, however there is no chance of running the pcv line to either one of the ports under the GT40 manifold. Nothing but a tapered plug will...
  14. N

    306 N/A 11.1 Compressions Plug Gap?

    Any suggestions? Thanks for the help!
  15. N

    GT40 Intake Gasket Help

    ahhh do you mean I have the wrong gasket on for the lower intake? I did not check the gasket up against the manifold, but I did put them against the head and they matched up. The way I look at it I know that this manifold bolted to these heads on the guys car I bought them from. And the...
  16. N

    GT40 Intake Gasket Help

    I put the Felpro MS93334 gaskets on. GT40 lower maniford winsor jr cast iron head. Are these correct?
  17. N

    GT40 Intake Gasket Help

    ok I put my GT40 lower intake on last week. I used the lower gaskets from a 90 5.0. The year of my block. All of the bolts lined up perfect. Now I see that I need other ones for the upper gasket. But are all of the lower gaskets the same? Do the ports line up correctly? Or do I need a cobra...
  18. N

    75 MM Throttle Body for my setup?

    I may be picking up a used one. Heres my setup 306 X cam Windsor Jr cast iron heads 24lbs injectors 75 mm a good size? Thanks
  19. N

    Stock Valve Covers with 1.6 rockers?

    I haven't tried to fit them yet, but will my stock 1990 5.0 Valve covers clear my harland sharp 1.6 rockers? I have heard yes and no. If they do not fit which aftermarket covers should I go with? Do I need ones that are higher? And do I have to worry about clearance on the intake manifold. I'm...
  20. N

    Few Questions before my GT40 Intake Install

    actually no its a true GT 40 intake. Maybe I misread the instructions. If it is the GT 40 intake from Ford racing all the holes should be tapped correct?
Top Bottom
Back
Forums
Menu