Search results

  1. T

    I made a boo boo (drag racing)

    Talk to a good lawyer. The $500 - 1000 you pay him will be cheaper than your fine and the cost of your insurance going up for 3 years.
  2. T

    Has anyone lost to an srt4. Be honest

    I have raced the srt4 in my gt, but not in my lightning. My gt is a good bit faster than my lightning. I don't know if the one I raced was stock or not, but he was keeping up pretty good. I didn't start pulling away till about 80mph.
  3. T

    Received an E-cam as a gift

    Even if it is not worth the horsepower it is definitly worth it for the sound. Even a stock headed cammed engine sounds bad a$$
  4. T

    What numbers should I exspect?

    with that setup you should be able to do low 8s to high 7.
  5. T

    Is 200 lbs of cylinder pressure high

    I pulled the intake off and the pushrods were bent.
  6. T

    Is 200 lbs of cylinder pressure high

    all the 8 cylinders were reading that high
  7. T

    Is 200 lbs of cylinder pressure high

    I bent a couple of push rods so I did a compression test to see if the valves might be bent. The cylinder that had the bent push rods read 195 lbs and the highest cylinder was 205. I know stock should be between 130-160. My heads are afr 165 with a 58cc chamber. Would this be why my cylinder...
  8. T

    I need help spending my money

    My drivability is fine. If I were to do longtubes would I still be able to pull the transmission without removing the headers?
  9. T

    I need help spending my money

    what is the difference between the crane hi-6s ingnition and the hi 6 with the lx-92 coil. I am looking in summit magazine now and the hi6s specifies for use with a 86-95 mustang.
  10. T

    I need help spending my money

    That is a good one. I did not even think about that. I will definitly get one of those. I don't want to get slicks because I have yet to put subframe connectors on. I am going to order my suspesion from either maximum motorsports or saleen and both of those come with the connectors. I have...
  11. T

    I need help spending my money

    I have to order new push rods and new lifters for my car. I have to spend $500 with summit to get 0% for a year. I figure the lifters and pushrods will run my about $200 so I have to spend at least 300 more. I am thinking either a steel or aluminum flywheel, or a mds 6al ignition. With my...
  12. T

    AFR 165 head plugs!? *Help*

    The ford dealer charges something like $8 apiece for those. I used the trickflow plugs on mine and I ordered it through summit for like $2. The trickflow part number is TFS-51400265.
  13. T

    bent pushrods do I need to pull my head

    They seemed to have good clearance between the valvespring and the were centered up pretty good on the top of the spring. Are chromemoly alot stronger than the standard hardened push rods?
  14. T

    bent pushrods do I need to pull my head

    My bad the push rod on the intake and exhaust valve is bent. The valve itself does not appear to be bent. I am just running a b cam also so I really do not have that much lift. So I do not think that it was a pistion to valve clearance problem and like I said earlier I have been running this...
  15. T

    bent pushrods do I need to pull my head

    I was running my car last night when it started making a awfull knocking noise. The car was firing back through the intake runner on the number 4 cylinder. It bent the exhast valve on #4 real bad and it also bent the intake, but the intake was still opening enough for the air to fire back out...
  16. T

    knocking noise and blowing back through the intake

    Well my car was not running like crap. I just bought a lightning about a month ago and it just turned 1k miles. I had not got on the lightning yet so I took both out to see which was faster. Me and my buddy ran for about a 1/4 mile. My mustang walked my lightning by about 2 carlengths before...
  17. T

    knocking noise and blowing back through the intake

    I was out running my car tonight and I got it too about 5000rpms in third gear when something let loose. It sounds like something is hitting the valve cover on the passengers side. I took off the upper intake but I was to tired to go any farther. When I turned the motor over the last cylinder...
  18. T

    Start Stall after 95 Cobra intake install

    You might want to check your timing first. I would also check all my vacuum lines. There are a couple of holes that need to be plugged on the intake I would check all of those. Make sure you plugged the fuel pump shutoff switch back in.
  19. T

    95 Mustang GT help with tranny

    I would not consider a t5 an upgrade. If I was going to spend that kind of money for a t5 conversion I would just save it and buy a tremec tko or a t56.
  20. T

    Cobra Intake questions?

    I would skip the gastets cause they don't line up at all. On my spacer I just used high temp orange rtv. I did the lower intake first and just spread it evenly and thin then i took some short bolts and finger tightend them to hold the spacer down till it was dry. Then I did a thin layer up...
Top Bottom
Back
Forums
Menu