Search results

  1. Lifted94XLT

    Mustang Interchangeability?

    you link is just takin me to the oreilly website bud. no product shown.
  2. Lifted94XLT

    Need a Rear Brake Line Pic Please!!

    That's the piece I dont have.... do any aftermarket companies sell this or am I stuck with the dealer or a junkyard?? And thank you for the great pics!! :nice: --Ryan
  3. Lifted94XLT

    Need a Rear Brake Line Pic Please!!

    Thanks for the quick reply, but I actually need a pic of how the Other side mates up to the body hardline (where the banjo fittin under the blue tape screws into). That's one mighty fine lookin rearend though. Haha
  4. Lifted94XLT

    Need a Rear Brake Line Pic Please!!

    I have replaced all my hardlines with aftermarket pre-bent ones form Classic Tube Industries and I went today and bought the center rubber brake line for the axle. As this was a 4cyl car to begin with, I never got to see how the hard line was mated to the "Banjo fitting Block" on the soft line...
  5. Lifted94XLT

    Rear brake line, fuel line help for 89 foxbody,5.0

    The block on the end of the soft line is for a banjo fitting. and I'm tryin to figure out how it attaches to the factory rear brake line also. As far as the fuel lines, this is how I ran mine..... well dang, I can't get my pics to work.... I have all my build pics on my Facebook page, and I...
  6. Lifted94XLT

    Anti-theft - Kill switch...

    ok, my question is then:: I am using a speed density engine harness with the FRP Mass Air Conversion Harness, so does that mean I don't have a fuel pump relay? that's not good. :shrug:
  7. Lifted94XLT

    4cyl Spring Length

    Thank you!! That's bad for me though. I have mystery springs apparently.... Gotta find 4cyl. springs. Thanks man! --Ryan
  8. Lifted94XLT

    Anti-theft - Kill switch...

    Ok. Thanks. Is the fuel pump relay in a dofferent location than under the seat then? Because its not there. Its a 92 4cyl.
  9. Lifted94XLT

    4cyl Spring Length

    I'm puttin in the 4cyl springs into my front control arms, and they seam WAY long! I'm wonderin if in the mix n match of this car to my v8 donor car the springs got mixed up or something. does anyone have the length of the 4cyl springs?? mine measure out to be just about 14"..... any help would...
  10. Lifted94XLT

    Anti-theft - Kill switch...

    Anybody know this?
  11. Lifted94XLT

    Anti-theft - Kill switch...

    I know this is an old post, but I have a quick question. I am gettin ready to wire in a fuel pump cut-off switch on my 92 Mustang. the thing is, that I have done a 5.0 conversion so the body harness (with the fuel pump wiring) is still 4cyl. my question is:: where is the fuel pump relay on the...
  12. Lifted94XLT

    2010 Hot Rod Power Tour

    I'm thrashin on my car to get it ready this year. is anybody else planning on goin?
  13. Lifted94XLT

    4cyl to 302 throttle cable

    Is the Throttle cable the same between the 4cyl and the 302?? Also, could somebody do me a HUGE favor and snap a pic of how it is ran behind the motor and hooked to the throttle body? I would greatly appreciate it. IIRC from when I tore the 302 out of the donor, there was a throttle bracket that...
  14. Lifted94XLT

    Crossmember to Trans Mount Bolt Size?

    That helps tremendously. Thanks man.... Yea, the 13tpi is throwin me off a bit. I'll see if I can find that, if not, hopefully a 12 will work
  15. Lifted94XLT

    Crossmember to Trans Mount Bolt Size?

    As the title states, i'm finishin up my 302/T5 swap and put the trans crossmember in today, but I have lost the bolts that attach the trans mount to the crossmember. Does anyone know the specs on these? oh yeah, if it matters, and it probably does, the trans mount is from Prothane. Thanks --Ryan
  16. Lifted94XLT

    Regarding NHRA rules w/ Nitrous

    Perfect!! I have to build something for behind the seats, so I may build on anyway, justin case. :D I appreciate the help and the clarification> Thanks! --Ryan
  17. Lifted94XLT

    Regarding NHRA rules w/ Nitrous

    Kind of a dumb questions as I think I already know the answer, but I wanna make sure. Do I still need to fabricate a firewall in my coupe behind my rear seats (the factory fiberboard one is deteriorated) if I'm gonna have a blow down tube exiting the car? I think I do, but I thought I'd verify...
  18. Lifted94XLT

    new wheels just arrived

    I have them for my notch. They are not on the car right now as I'm still building the car. I have 15x3.5s w/ 195/55x15 Nitto NT450s on the front and 15x8s w/ 275/60x15 MT Drag Radials on the Rear. I love how they look. I wish I had a better pictures of how they looked on the car when I test...
  19. Lifted94XLT

    water pump bolts

    Thanks, that's a lot of decipherin!! thanks though.... I really hope I can get the ARP bolts to work, but its lookin kinda grim at this point
  20. Lifted94XLT

    water pump bolts

    revivings a VERY old Thread..... I have a problem, my motor got torn down last year, and I guess I wasn't as organzied as I thought, and I can't find me old water pump bolts. No biggie, I bought an ARP Bolt kit and the bolts that come in the kit for the water pump don't fit..... well, two do...
Top Bottom
Back
Forums
Menu